Bosch LTC 8808/00 Series, Инструкция по эксплуатации

Страница: 82 / 126

76 | en LTC 8600 | LTC 8800 Series
Bosch Security Systems, Inc. Instruction Manual F.01U.127.393 | 2.0 | 2009.03
User Function 13 - Print System Configuration Tables
Use this function to print the contents of the various system configuration tables.
Move the joystick up and down to select a table, then press
[Enter]
to send it to the
printer port. If using the LTC 8555 Series keyboard, press
[User]
to exit.
User Function 14 - Reserved Function
User Function 15 - System Reset
The system may be reset from the keyboard. After entering this mode, the video
monitor screen indicates
RESET SYSTEM
. Enter the password via the numeric key-
pad, and press
[Enter]
. The system will then reset. If using the LTC 8555 Series key-
board, press
[User]
to exit the mode without resetting the system.
NOTE: The system should be reset whenever a change is made on the main CPU
module's DIP switches. Alternatively, the main power to the CPU bay may be
switched off for ten (10) seconds, then restored. Depending on the size and com-
plexity of the system, several seconds may be required before operation is restored.
This time is due to the amount of initialization tasks being performed, and is consid-
ered normal.
User Function 16 - Time Event Enable/Disable
Use this function to enable or disable any of the programmed time event functions.
Up to 64 time event functions can be programmed with the optional LTC 8059/00
MCS, or the LTC 8850/00 GUI Software. Moving the joystick up and down steps
through a table of the 64 time events. If an event has been programmed, moving the
joystick to the right enables the event, and to the left disables it. The current status
of an enabled time event is displayed by this user function.
User Function 17 - Set Monitor ID
User Function 17 is used to enter a (12-character) monitor identification message
for display in the top line of the monitor overlay display on any system monitor(s).
This monitor title will be visible on the display regardless of the camera currently
being viewed. This message can be used to identify the particular monitor or a
group of cameras assigned to this monitor. See Chapter 20, “Character ROM Tables
for LTC 8600 and LTC 8800,” on page 86 for the available characters.
After entering the mode, the joystick is moved right or left to select the character to
be changed. The selected character is identified by a box with a question mark
inside it. The first line of the video monitor display indicates the code number of the
character selected. Move the joystick up or down to step through the Character
ROM Table, or enter the character's number identified in the Tables via the numeric
keypad, then press
[Enter]
. Once the monitor title has been set, press
[Enter]
to store
it to memory. If using the LTC 8555 Series keyboard, press [
User]
to exit the mode.
The user may select between this monitor message and the status display by using
the User 5 Function described above.
User Function 18 - Print Sequence
Use this function to print the contents of a programmed sequence. Use the joystick
to select the desired sequence, then press
[Enter]
to print it to the printer port. Only
those sequences currently existing in memory will be shown in the list. If using the
LTC 8555 Series keyboard, press
[User]
to exit.
User Function 19 - Select Alarm Response
Use this function to reset the system alarm configuration tables to one of these pre-
defined alarm response modes:
BASIC
,
AUTOBUILD
, or
SEQUENCE & DISPLAY
.
Move the joystick up or down to select the desired mode, then enter your user pass-
word on the numeric keypad. Press
[Enter]
to update the alarm system. If using the
LTC 8555 Series keyboard, press
[User]
to exit.
NOTE
Existing alarm configuration data will be lost when mode is changed.