Bosch HBC38D753, Инструкция по эксплуатации

Страница: 7 / 40

7
Moisture sensor
The moisture sensor is located at the top on the right of the
cooking compartment ceiling. When types of heating involving
steam are used, it measures the moisture content in the
cooking compartment.
You save energy and water because only so much steam as is
required is produced.
Steam condenses on the moisture sensor and drips down. This
is normal.
Caution!
When cleaning the moisture sensor, do not bend or push in the
sides. That may cause malfunctions.
Before using the appliance for the first time
In this section you will find out which steps are required before
using the appliance for the first time:
■
Setting the clock and language
■
Setting the water hardness range
■
Starting the appliance for the first time
■
Cleaning the accessories before use
■
Fitting the grease filter
Setting the clock and language
When your new appliance is connected, "Uhrzeit einstellen" (set
clock) appears in the display. Set the clock and the language
for the display, if required.
1.
Press the
X
button to switch to the default time.
2.
Set the current time using the rotary selector.
3.
Press the
Y
button to switch back to "Uhrzeit" (clock).
4.
Turn the rotary selector to switch to "Sprache auswählen"
(select language).
5.
Press the
X
button to switch to "deutsch".
6.
Set the required language using the rotary selector.
30 different languages are available.
7.
Press the
0
button.
The time and language are applied. The current time is
displayed.
Setting the water hardness range
Descale your appliance regularly. This is the only way to
prevent damage.
Your appliance automatically displays when it needs descaling.
It has been preset to water hardness range "medium". Change
the value if your water is softer or harder.
You can check the water hardness with the test strips supplied
or ask your water supplier.
If your water is very hard, we recommend that you use softened
water.
You can only dispense with descaling completely if you
exclusively use softened water. If this is the case, change the
water hardness to "softened".
You can change the water hardness range in the basic settings
when the appliance is switched off.
1.
If required, press the % button to switch off the appliance.
2.
Press and hold the
°
button until "Select language" appears in
the display.
3.
Turn the rotary selector until "Water hardness range" appears.
4.
Press the X button.
"2-medium" is highlighted in the display.
5.
Change the water hardness range using the rotary selector.
Possible values:
6.
Press the
°
button to exit the basic settings.
The change is saved.
Before first use
Before first use, heat the empty appliance for 20 minutes at
100 °C with the Steam type of heating. Do not open the
appliance door during this time. The appliance is automatically
calibrated (see section: Automatic calibration).
1.
Press the % button to switch on the appliance.
The "Hot air" type of heating appears after approx.
4 seconds.
2.
Fill the water tank and insert it (see section: Filling the
water tank).
Before using for the first time, moisten the tank cover seal
with a little water.
3.
Turn the rotary selector until "Steam" appears.
4.
Press the n button.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation automatically ends and a signal
sounds.
5.
Press the % button to switch off the appliance.
Leave the appliance door ajar until the appliance has cooled
down.
Cleaning the accessories before use
Using soapy water and a soft cloth, clean the accessories
thoroughly before first use.
2EHU8QWHUKLW]H
ƒ&
8KU]HLWHLQVWHOOHQ
8KU]HLW
PLW VFKOLH‰HQ
softened -
1-soft I
2-medium II
3-hard III
4 ­ very hard IV