12
| English
2 610 017 766 | (5.10.11)
Bosch Power Tools
32
Extraction adapter (non-plunge base)*
33
Intermediate ring for extraction adapter (non-plunge
base)*
34
Scale for depth-of-cut adjustment
(non-plunge base)
35
Parallel guide*
36
Guide rod for parallel guide (2x)*
37
Wing bolt for fine adjustment of parallel guide (2x)*
38
Wing bolt for coarse adjustment of
parallel guide (2x)*
39
Fine-adjustment knob for parallel guide*
40
Adjustable edge guide for parallel guide *
41
Wing bolt for guide rods of parallel guide (2x)*
42
Router compass/guide-rail adapter*
43
Router compass handle*
44
Wing bolt for coarse adjustment of
router compass (2x)*
45
Wing bolt for fine adjustment of
router compass (1x)*
46
Fine-adjustment knob for router compass*
47
Centring screw for compass stop *
48
Base spacer
(included in the “router compass” set)*
49
Guide rail*
50
SDS guide-bushing adapter
51
Fastening screw for guide bushing adapter (2x)
52
Release lever for guide bushing adapter
53
Guide bushing
54
Fastening screw for guide plate
55
Centring pin
56
Fastening screws for non-plunge base*
57
Specialty Allen key for depth-of-cut fine adjustment
(non-plunge base)*
58
Extension for depth-of-cut fine adjustment
(non-plunge base)*
59
Extraction hood for edge routing *
60
Fastening screw for extraction hood *
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Assembly
f
Before any work on the machine itself, pull the mains
plug.
Inserting the Routing Motor into the Plunge
Base/Non-plunge Base (see figures A–B)
– Open the clamping lever for the plunge base/non-plunge
base
22
.
– Push the routing motor to the stop into the plunge
base/non-plunge base.
– When using the non-plunge base
3
, press clamping lever
25
and slide the routing motor
1
up or down to the desired
position in the non-plunge base
3
, until it, with the clamp-
ing lever
25
released, engages in one of the 3 notches
26
.
– Shut the clamping lever for the plunge unit/non-plunge
base
22
.
– Adjust the required depth-of-cut; see Section “Adjusting
the Depth-of-cut”.
Separating the Routing Motor from the Plunge Unit/Non-
plunge Base (see figure C)
– Open the clamping lever for the plunge base/non-plunge
base
22
.
Multifunction Router
GOF 1600 CE
Professional
GMF 1600 CE
Professional
Article number
3 601 F24 0..
3 601 F24 0..
Rated power input
W
1600
1600
No-load speed
min
-1
10000 – 25000
10000 – 25000
Speed preselection
z
z
Constant electronic control
z
z
Connection for dust extraction
z
z
Tool holder
mm
inch
8 – 12
¼ – ½
8 – 12
¼ – ½
Plunge depth (plunge base)
mm
76
76
Weight according to EPTA-Procedure 01/2003
– Contour router
– Plunge router
kg
kg
–
5.8
4.3
5.8
Protection class
/
II
/
II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
OBJ_BUCH-1559-001.book Page 12 Wednesday, October 5, 2011 7:48 AM
