10
| English
1 609 92A 0KN | (13.6.14)
Bosch Power Tools
Product Features
The numbering of the product features refers to the illustra-
tion of the drill stand on the graphics pages.
1
Drilling lever with drilling-depth scale
2
Screw for the side holder
3
Side holder for drill
4
Drill fixture
5
Screw for drill fixture
6
Motor On/Off switch
7
Socket outlet for drill
8
Magnet On/Off switch
9
Insulated gripping surfaces
10
Safety chain
11
Lock nut
12
Set screw for adjustment of the guide rail
13
Open-end spanner
14
Hex key
A complete overview of accessories can be found in our accesso-
ries program.
Technical Data
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: –.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
19.05.2014
Assembly
Inserting the Drill
Remove the auxiliary handle from your drill, if required (see
the operating instructions of the drill).
Loosen screw
5
using an Hex key. Insert the drill with the drill
collar from above into the drill fixture
4
to the stop. Mount
screw
2
in order to connect the drill with the side holder
3
.
Hand-tighten screw
5
using an Hex key.
Check the tight seating of the drill in the drill fixture.
When the drill is not securely fastened, serious injury may
result.
Mounting the Safety Chain (see figure A)
For all work being performed in inclined, vertical or overhead
positions, secure the drill stand against falling down with the
provided safety chain
10
.
Before using the safety chain, check its proper func-
tion. Never use a damaged safety chain; replace a dam-
aged safety chain immediately.
Fasten the safety chain in such a manner that the drill stand
moves away from you, should it come undone.
Fasten the safety chain around the carrying handle of the drill
stand with as little play as possible.
Operation
Pull the plug from the socket outlet and/or remove the
battery before carrying out adjustments on the power
tool or replacing accessory parts.
Unintentional starting
of drills is the cause of some accidents.
After each adjustment on the drill stand, retighten the
bolts and locking handles.
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
Insert the mains plug of the drill only into socket outlet
7. Switch the drill on and lock the On/Off switch of the
drill with the lock-on button.
Otherwise, the drill cannot
be switched on or off via the motor On/Off switch
6
on the
drill stand.
Push the magnet On/Off switch
8
upward and check if the drill
stand adheres to the workpiece surface.
To
start
the drill, press the motor On/Off switch
6
to position
“
I
”.
Note:
The drill can only be started when the magnet has al-
ready been switched on.
To switch off the drill, press the motor On/Off switch
6
to po-
sition “
0
”.
Wait until the drill has come to a complete stop before push-
ing the magnet On/Off switch
8
downward in order to switch
the magnet off.
When not using the drill, switch it off in order to save energy.
Magnetic drill stand
GMB 32
Article number
0 601 193 0..
Rated power input
W
95
Holding force of the magnet
kN
25
Max. drilling dia.
(GBM 32-4, MK3 tool holder)
– Twist drill bit
– Core bit
mm
mm
32
12 – 60
Drill stroke, max.
mm
223
Diameter of drill fixture
mm
65
Weight according to
EPTA-Procedure 01/2003
kg
26
Protection class
/
I
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-1761-002.book Page 10 Friday, June 13, 2014 8:07 AM
