English |
11
Bosch Power Tools
1 609 92A 01D | (11.2.13)
fore, use only sharp saw blades that are suited for the material
to be worked.
Sawing Wood
The correct selection of the saw blade depends on the type
and quality of the wood and whether lengthway or crossway
cuts are required.
When cutting spruce lengthways, long spiral chips are formed.
Beech and oak dusts are especially detrimental to health.
Therefore, work only with dust extraction.
Sawing with Parallel Guide (see figure D)
The parallel guide
8
enables exact cuts along a workpiece
edge and cutting strips of the same dimension.
Sawing with Auxiliary Guide (see figure E)
For sawing large workpieces or straight edges, a board or
strip can clamped to the workpiece as an auxiliary guide; the
base plate of the circular saw can be guided alongside the aux-
iliary guide.
Sawing with Guide Rail (see figure G)
The guide rail
33
is used to carry out straight cuts.
Note:
Use the guide rail
33
only for right-angled cuts. When
using for mitre cuts, the guide rail
33
can become damaged.
The adhesive coating prevents the guide rail from slipping and
protects the surface of the workpiece. The coating of the
guide rail allows the circular saw to glide easily.
Place the circular saw directly onto the guide rail
33
. Fasten
the guide rail
33
with suitable clamping devices, e. g., screw
clamps, on the workpiece in such a manner that the narrow
leg of the guide rail
33
faces toward the saw blade.
The guide rail 33 must not extend beyond the face side of
the workpiece where the cut is to be started.
Switch the machine on and guide it in the cutting direction ap-
plying moderate and steady feed.
Two guide rails can be connected to one with use of the con-
nection piece
34
. Clamping is carried out with the four screws
located in the connection piece.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Store the battery only within a temperature range between
0 °C and 50 °C. As an example, do not leave the battery in the
car in summer.
Occasionally clean the venting slots of the battery using a soft,
clean and dry brush.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
For safe and proper working, always keep the machine
and ventilation slots clean.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean. Remove dust and
chips by blowing out with compressed air or with a brush.
Saw blades that are not coated can be protected against cor-
rosion with a thin coat of acid-free oil. Before use, the oil must
be removed again, otherwise the wood will become soiled.
Resin and glue residue on the saw blade produces poor cuts.
Therefore, clean the saw blade immediately after use.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch’s application service team will gladly answer questions
concerning our products and their accessories.
People’s Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 4008268484
Fax: (0571) 87774502
E-Mail: [email protected]
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
E-Mail: [email protected]
www.bosch-pt.com.hk
Indonesia
PT. Multi Mayaka
Kawasan Industri Pulogadung
Jalan Rawa Gelam III No. 2
Jakarta 13930
Indonesia
Tel.: (021) 46832522
Fax: (021) 46828645/6823
E-Mail: [email protected]
www.bosch-pt.co.id
OBJ_BUCH-765-002.book Page 11 Monday, February 11, 2013 11:29 AM
