English |
25
Bosch Power Tools
1 619 929 797 | (3.2.09)
Adjusting the Drilling Depth on the Dust Ex-
traction Attachment (see figure H)
The required drilling depth
X
can also be adjust-
ed when the dust extraction attachment is
mounted.
– Insert the SDS-plus drilling tool to the stop
into the SDS-plus tool holder
2
. Otherwise,
the movability of the SDS-plus drilling tool
can lead to incorrect adjustment of the drill-
ing depth.
– Loosen the wing bolt
24
on the dust extrac-
tion attachment.
– Without switching the power tool on, apply it
firmly to the drilling location. The SDS-plus
drilling tool must face against the surface.
– Position the the guide pipe
25
of the dust ex-
traction attachment in its holding fixture in
such a manner that the head of the dust ex-
traction attachment faces against the surface
to be drilled. Do not slide the guide pipe
25
further over the telescopic pipe
23
of the
dust extraction attachment than required, so
that as much as possible of the scale
23
on
the telescopic pipe remains visible.
– Retighten the wing bolt
24
again. Loosen the
clamping screw
21
on the depth stop of the
dust extraction attachment.
– Move the depth stop
22
on the telescopic
pipe
23
in such a manner that the
clearance
X
shown in the figure corresponds
with the required drilling depth.
– Tighten the clamping screw
21
in this posi-
tion.
Operation
Starting Operation
Inserting the Battery
f
Use only original Bosch lithium ion batter-
ies with the voltage listed on the nameplate
of your power tool.
Using other batteries can
lead to injuries and pose a fire hazard.
– Set the rotational direction switch
6
to the
centre position to protect the power tool
against accidental starting.
– Insert the charged battery
11
from the front
into the base of the power tool. Push the bat-
tery completely into the base until the red
stripe can no longer be seen and the battery
is securely locked.
Setting the Operating Mode
With the selector switch for drilling/hammer
drilling
8
, the operating mode of the machine is
selected.
Note:
Change the operating mode only when the
machine is switched off! Otherwise, the ma-
chine can be damaged.
– To change the operating mode, turn the se-
lector switch for “drilling/hammer drilling”
8
to the requested position.
Reversing the Rotational Direction
(see figure I)
The rotational direction switch
6
is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch
7
actuated.
Right rotation:
Push the rotational direction
switch
6
left to the stop.
Left rotation:
Push the rotational direction
switch
6
right to the stop.
For hammer drilling and drilling, always set the
direction of rotation to right rotation.
Switching On and Off
– To
start
the machine, press the On/Off
switch
7
.
When starting the machine for the first time, a
starting delay is possible, as the electronic sys-
tem of the power tool has to configure itself
first.
– To
switch off
the machine, release the
On/Off switch
7
.
Position for
hammer drilling
in con-
crete or stone
Position for
drilling
without impact
in wood, metal, ceramic and plastic
as well as for screwdriving
OBJ_BUCH-518-002.book Page 25 Tuesday, February 3, 2009 12:02 PM
Содержание GBH 36 V-LI Compact
Страница 3: ...3 1 619 929 797 3 2 09 Bosch Power Tools X 16 2 1 9 19 18 17 4 18 4 10 16 F E D C B A ...
Страница 4: ...1 619 929 797 3 2 09 Bosch Power Tools 4 20 16 9 X 21 22 23 24 25 6 26 4 J I H G ...
Страница 5: ...5 1 619 929 797 3 2 09 Bosch Power Tools 2 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ...
