Bosch FPA-1200-MPC-C Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 100

background image

Panel Controller

Diagnostics | en

65

Bosch Sicherheitssysteme GmbH

User Guide

2017.09 | 7.0 | F.01U.258.929

1.

In the start menu, select

Diagnostics

2.

Network services

3.

Routing table

A table with routing information is displayed.

All networked nodes that can be reached via the node currently being operated and that are
recognized within the system network are displayed under

Node

.

CAN1 to USB1 designate the interfaces on the currently operated panel node. In this example,
it is the node 1 interfaces.
The type of interface on the panel node currently being operated is listed under

interface

.

The following interfaces can be designated:
–

CAN 1 interface

–

CAN 2 interface

–

Ethernet 1 (IP multicast or UDP tunnel)

–

Ethernet 2 (IP multicast or UDP tunnel)

–

Serial Interface

–

USB 1 interface

The number of nodes that need to be passed in order to reach the listed node is entered
under

distance

. For nodes that are directly reachable via IP multicast, the value is 1; for nodes

that are connected via other interfaces (e.g. CAN) to nodes reachable via IP multicast, the
value is increased in increments accordingly (e.g. connected via IP mul CAN1/CAN2,
value = 2).
A node number from 1 to 64 can be assigned to panels. All numbers above 240 (241-255) are
assigned dynamically and used, for instance, for an OPC server or a PC with FSP-5000-RPS
software.

14.7.2

Consistency check

Inconsistencies between the network settings configured in FSP-5000-RPS and those set in
the panel controller are displayed under

Diagnostics

-

Network services

-

Consistency check

.

1.

In the start menu, select

Diagnostics

2.

Network services

3.

Consistency check

Where inconsistencies are identifiable between the network settings saved in the panel
controller and those configured in FSP-5000-RPS, these are indicated. You can use the
arrow key on the display to alternate between displaying

Problems of active

configuration

and

Problems expected after restart

.

Problems of active configuration

The table indicates inconsistencies between the network settings of the panel controller's
active configuration ("

active

") and the settings configured in RPS ("

configured

").

Problems expected after restart

The table indicates inconsistencies between the network settings that have already been
configured on the panel but which do not take effect until restart ("

saved

") and the settings

configured in RPS ("

configured

").

14.7.3

Ethernet ports

To display a table listing the various parameters and the status of the two Ethernet ports:
1.

In the start menu, select

Diagnostics

2.

Network services

«
...
63
64
65
66
67
...
»

Содержание FPA-1200-MPC-C





































































































Отзывы:

Нет отзывов

Похожие инструкции для FPA-1200-MPC-C

Бренд: NCR Страницы: 6

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Balboa Water Group Страницы: 28

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: Barco Страницы: 6

Бренд: ECKELMANN Страницы: 178

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 11

Бренд: IFM Electronic Страницы: 23

Бренд: brel-motors Страницы: 2

Бренд: SMC Networks Страницы: 15

Bilge Pump Control Panel

Бренд: SPXFLOW Страницы: 14

Бренд: Eaton Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды