Bosch FPA-1200-MPC-C Скачать руководство пользователя страница 13

Страница: 13 / 100

Panel Controller

All functions at a glance | en

Bosch Sicherheitssysteme GmbH

User Guide

2017.09 | 7.0 | F.01U.258.929

–

Isolate or de-isolate an element

3.3

Diagnostics

Element details

Modules

Hardware

Panel passport

LED test on modules

History log

Network services

VAS

Element details

–

All info for one element

: Display all diagnostic information about an element on a loop of

an LSN module.

–

Info for element group

: Select and display specific pieces of diagnostic information

about several elements in the selected LSN module.

–

Info for all elements on the module

: Select and display specific pieces of diagnostic

information about all LSN elements of the selected LSN module.

Modules

–

Module passport

: Display diagnostic information for each individual module: production

data, software version, CAN ID, compatibility.

–

Module Compatibility

: Display the software version of the selected module in

comparison with the control panel software version.

–

Module status

: Display hardware diagnostic data for the selected module.

Only for LSN modules:
–

Module status and counters

–

Reset counters

: Reset the counters that record the frequency with which various events

occur.

Hardware

–

Address cards

: Additional display for each card slot of the serial number and number of

addresses per card.

–

Display

–

LED test

: Test all LED displays on the panel controller. These remain lit for the

duration of approx. five seconds.

–

Key test

: Test the operativeness of the membrane keypad.

–

Display test

: Test the operativeness of the display.

–

Display touch test

: Test the operativeness of the touch-sensitive surface.

–

Adjust touch screen

: Adjust the location precision when touching the touchscreen.

–

Serial interface

: Display statistical data for the transmission.

–

CAN bus

: Display status of CAN interfaces.

Panel passport

Display diagnostic information such as manufacturing data or software version of the panel
controller.

LED test on modules

Test LED displays of individual modules and simultaneously test all LED displays.

History log

See Maintenance – History log

Network services

–

Routing table

Содержание FPA-1200-MPC-C





































































































Результаты поиска

Содержание FPA-1200-MPC-C

Отзывы:

Похожие инструкции для FPA-1200-MPC-C

Бренды по названию

Популярные бренды

Bosch FPA-1200-MPC-C, Руководство пользователя

Результаты поиска

Содержание FPA-1200-MPC-C

Отзывы:

Похожие инструкции для FPA-1200-MPC-C

Бренды по названию

Популярные бренды