Bosch FlexiDome NDN-498V03 Скачать руководство пользователя страница 28

Страница: 28 / 138

en | Installation

FlexiDome2X IP Camera

AR18-10-B006 | v1.1 | 2010.06

Installation and Operation Manual

Bosch Security Systems

Remove the trim ring with dome by pulling it off of the

base.

Remove the inner liner by pulling it off of the base.

Remove the pink protection foam.

Loosen the three Phillips screws. Remove the single screw

holding the camera module in place (no keyhole).

Rotate the camera module to remove it from the remaining

two screws.

5.1.2

Flush mount version

The camera/housing unit consists of the following parts:

To disassemble the unit proceed as follows:

Using the special screwdriver bit, loosen the three tamper-

resistant screws in the trim ring (the screws remain in

place).

Remove the trim ring with dome by pulling it off of the

base.

Remove the inner liner by pulling it off of the base.

Camera module and mounting base

Inner liner (with sealing ring)

Dome

Trim ring

Содержание FlexiDome NDN-498V03











































































































































Результаты поиска

Содержание FlexiDome NDN-498V03

Отзывы:

Похожие инструкции для FlexiDome NDN-498V03

Бренды по названию

Популярные бренды

Bosch FlexiDome NDN-498V03, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FlexiDome NDN-498V03

Отзывы:

Похожие инструкции для FlexiDome NDN-498V03

Бренды по названию

Популярные бренды