Bosch FlexiDome NDN-498V03 Скачать руководство пользователя страница 105

Страница: 105 / 138

FlexiDome2X IP Camera

Advanced Mode | en

105

Bosch Security Systems

Installation and Operation Manual

AR18-10-B006 | v1.1 | 2010.06

To limit connections to SSL encryption, set the

Off

option in

the HTTP browser port, the RCP+ port, and Telnet support. This

deactivates all unencrypted connections allowing connections

on the HTTPS port only.

Configure and activate encryption for media data (video, audio,

metadata) on the

Encryption

page.

RCP+ port 1756

Activating RCP+ port 1756 allows unencrypted connections on

this port. To allow only encrypted connections, set the

Off

option to deactivate the port.

Telnet support

Activating Telenet support allows unencrypted connections on

this port. To allow only encrypted connections, set the

Off

option to deactivate telnet support, making telnet connections

impossible.

Interface mode ETH

If necessary, select the Ethernet link type for interface

ETH

Depending on the device connected, it may be necessary to

select a special operation type.

Network MSS (Byte)

Set the maximum segment size for the IP packet's user data

here. This gives the option to adjust the size of the data packets

to the network environment and to optimize data transmission.

Please comply with the MTU value of 1,514 bytes in UDP mode.

iSCSI MSS (Byte)

Specify a higher MSS value for a connection to the iSCSI

system than for the other data traffic via the network. The

potential value depends on the network structure. A higher

value is only useful if the iSCSI system is located in the same

subnet as the camera.

Содержание FlexiDome NDN-498V03











































































































































Результаты поиска

Содержание FlexiDome NDN-498V03

Отзывы:

Похожие инструкции для FlexiDome NDN-498V03

Бренды по названию

Популярные бренды

Bosch FlexiDome NDN-498V03, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FlexiDome NDN-498V03

Отзывы:

Похожие инструкции для FlexiDome NDN-498V03

Бренды по названию

Популярные бренды