Bosch FlexiDome NDN-498V03 Скачать руководство пользователя страница 121

Страница: 121 / 138

FlexiDome2X IP Camera

Troubleshooting | en

121

Bosch Security Systems

Installation and Operation Manual

AR18-10-B006 | v1.1 | 2010.06

No audio

transmission to

remote station.

Hardware fault.

Check that all connected

audio units are operating

correctly.

Faulty cable connections. Check all cables, plugs,

contacts and

connections.

Incorrect configuration.

Check audio parameters

on the

Audio

configuration and

LIVEPAGE Functions

pages.

The audio voice

connection is already in

use by another receiver.

Wait until the connection

is free and then call the

sender again.

The unit does not

report an alarm.

Alarm source is not

selected.

Select possible alarm

sources on the Alarm

sources configuration

page.

No alarm response

specified.

Specify the desired alarm

response on the Alarm

connections

configuration page; if

necessary change the IP

address.

Control of cameras

or other units is not

possible.

The cable connection

between the serial

interface and the

connected unit is not

correct.

Check all cable

connections and ensure

all plugs are properly

fitted.

The interface parameters

do not match those of the

other unit connected.

Make sure that the

settings of all units

involved are compatible.

Malfunction

Possible causes

Solution

Содержание FlexiDome NDN-498V03











































































































































Результаты поиска

Содержание FlexiDome NDN-498V03

Отзывы:

Похожие инструкции для FlexiDome NDN-498V03

Бренды по названию

Популярные бренды

Bosch FlexiDome NDN-498V03, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FlexiDome NDN-498V03

Отзывы:

Похожие инструкции для FlexiDome NDN-498V03

Бренды по названию

Популярные бренды