Bosch D4412 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 76

background image

D6412/D4412 Operation and Installation Guide

D6412/D4412

Page 11

© 2003 Bosch Security Systems

45349E

Overview

Minimum
Operating
Voltage

10.2 VDC

SDI Bus (Data)

12 VDC nominal. 305 m (1000 ft.) of 22 AWG (0.8 mm) cable.

Telephone
Connections

RJ31X or RJ38X jack can be interfaced with panel

Environmental

Temperature: 0°C to +50°C (+32° to +122°F)
Relative Humidity: 5% to 85% at +30°C (+86°F ) non-condensing

Arming Stations

•

D625 VF Text Command Center

•

D623 LCD Text Command Center

•

D621 LED Command Center

•

Keyswitch

Compatible
Enclosures

D2203 Universal Enclosure (included with panel), D8103 Universal Enclosure, D8109 Fire
Enclosure, D8108A Attack Resistant Enclosure.

Note: When ordering a compatible enclosure, order the D6412M (includes the mounting skirt
and the D6412LC) or the D4412M (includes the mounting skirt and the D4412LC). In addition,
order the CX4010 transformer.

Compatible
Accessories

•

D621 LED Command Center

•

D623 Text Command Center, LCD Display

•

D625 Text Command Center, Vacuum Fluorescent Display

•

DX2010 (D9528) Point Expansion Module

•

DX3010 (D9529) Octo-Output Module

•

DX3020 (X7410I) Module (not investigated by UL)

•

DX4010 (D9533) Serial Output Module (not investigated by UL)

•

DX8010 Telephone Command Module (not investigated by UL)

•

DS RF3224 Premises RF Receiver

•

DS RF3332/3334 Keyfob (not investigated by UL)

•

DS RF3341 Keypad (not investigated by UL)

•

Programming Key (PK32)

Control Panel
Configurations

•

D6412 - Complete control panel assembly in the D2203 Universal Enclosure. A CX4010
Transformer is supplied.

•

D6412LT - Complete control panel assembly in the D2203 Universal Enclosure. A CX4010
Transformer must be ordered separately.

•

D6412LC - Complete control panel assembly without an enclosure or transformer. A
CX4010 Transformer must be ordered separately.

•

D6412M - Complete control panel assembly with a mounting skirt for the compatible
enclosure. A CX4010 Transformer must be ordered separately. See Compatible Enclosures
in this table for compatible enclosure alternatives.

•

D4412 - Complete control panel assembly in the D2203 Universal Enclosure. A CX4010
Transformer is supplied.

•

D4412LT - Complete control panel assembly in the D2203 Universal Enclosure. A CX4010
Transformer must be ordered separately.

•

D4412LC - Complete control panel assembly without an enclosure or transformer. A
CX4010 Transformer must be ordered separately.

•

D4412M - Complete control panel assembly with a mounting skirt for the compatible
enclosure. A CX4010 Transformer must be ordered separately. See Compatible Enclosures
in this table for compatible enclosure alternatives.

«
...
9
10
11
12
13
...
»

Содержание D4412













































































Отзывы:

Нет отзывов

Похожие инструкции для D4412

FPBA-01 PROFIBUS DP

Бренд: ABB Страницы: 2

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: T-Verter Страницы: 121

Бренд: Happy Страницы: 10

Бренд: brel-motors Страницы: 2

LOWARA Aquavara IPC

Бренд: Xylem Страницы: 292

Бренд: Quantum Страницы: 20

Бренд: A10 Networks Страницы: 2

Бренд: Z-Wave Страницы: 5

Бренд: ICP DAS USA Страницы: 4

InRAX MVI46-PDPS

Бренд: ProSoft Technology Страницы: 72

Бренд: Broadcast Tools Страницы: 39

BLEUBOX R-IN-UHF-5239U

Бренд: iDTRONIC Страницы: 13

Бренд: Konig Страницы: 8

Бренд: Danfoss Страницы: 4

Cutler-Hammer S701X25N3BP

Бренд: Eaton Страницы: 4

Бренд: PI Страницы: 6

Бренд: Kaelus Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды