English - 9
Fit the chain and chain bar as described in “Assem-
bly and Tensioning Chain”.
The circular groove of the chain bar will wear partic-
ularly on the lower edge with time. When replacing
the chain turn the chain bar 180° to allow even wear,
thus extending chain bar life.
Reverse the chain tensioning catch 16 by removing
the screws and refitting it on the opposited side.
Check drive sprocket 21. If it is worn out or damaged
due to strain, have it exchanged by an authorized
Bosch service agent.
Have your chain sharpened professionally at your
Bosch approved service agent or sharpen the chain
yourself using the Bosch sharpening kit or a Dremel
power tool with the appropriate grinder (1453), both
available at your Bosch approved service agent. Fol-
low the sharpening instructions supplied with the
sharpening kit.
Proper functioning of the automatic oiler can be
checked by running the chain saw and pointing the
tip of the chain bar towards a piece of cardboard or
paper on the ground. Caution: Do not touch the
ground with the chain. Ensure safety clearance of
20 cm. If an increasing oil pattern developes, the au-
tomatic oiler is operating fine. If there is no oil pat-
tern, despite a full oil reservoir, see “Fault Finding” or
contact your Bosch approved service agent.
Chain
AKE 35-19 PRO
.........................................
F 016 800 239
AKE 40-19 PRO
.........................................
F 016 800 240
Chain bar
AKE 35-19 PRO
.........................................
F 016 800 241
AKE 40-19 PRO
.........................................
F 016 800 242
Cleaning
Chain sharpening/cleaning kit
.............
F 016 800 263
Chain oil 1 litre
..............................................
2 607 000 181
Chain oil 5 litre
.............................................
F 016 800 111
Additional accessories
Gloves
..............................................................
2 607 000 134
Protective goggles
.....................................
F 016 800 178
SNR 19 ear protectors
(sounding proofing level 19 dB (A))
...
2 607 990 042
SNR 24 ear protectors
(sounding proofing level 24 dB (A))
...
2 607 990 043
Clean the moulded plastic housing of the chain saw
using a soft brush and clean cloth. Do not use water,
solvents or polishes. Remove all debris, especially
from the motor cooling vents 27.
Remove and brush clean the cover plate 15, chain
and chain bar after 1 to 3 hours of use.
Clean the area under the cover plate 15, the drive
sprocket 21 and chain bar assembly using a soft
brush. Clean oil outlet 19 with a clean cloth.
If the chain tensioning mechanism becomes dif-
ficult to operate, dismantle the protective lid 29 from
inside the cover plate 15. Turn locking knob 14 and
red tensioning ring 13 against each other, so that
debris is loosened from the mechanism and can be
discarded. Carefully knock out debris. If mechanism
is heavily clogged, use a soft brush or compressed
air for cleaning. Do not use tools of any kind.
If the chain saw is to be stored for a longer period of
time, clean chain and chain bar.
Store in a secure, dry place out of the reach of chil-
dren. Do not place other objects on the chain saw.
To prevent leakage ensure machine is left in a hori-
zontal position (oil filler cap 4 uppermost).
When storing machine in original packaging the oil
tank must be completely emptied.
Replacing/Changing Chain
and Chain Bar
Sharpening Chain
Checking the Automatic Oiler
A
Accessories
Cleaning/Storage
B
J
F016 L70 532 - Buch Seite 9 Donnerstag, 15. Dezember 2011 2:58 14
26 • F016 L70 532 • 08.05
