Bosch 3 601 L30 200, Руководство по эксплуатации

Страница: 40 / 214

English– 13
1 619 P03 456 • (05.11) PS
Parallelism of the Saw Blade the Guide
Grooves of the Angle Guide
Place the power tool in the working position.
Swing back the protective hood 5 to the stop.
Checking: (see Figure )
With a pencil, mark the first left saw tooth that is visible
at the rear above the table insert.
Set the combination square to 90° and place it on the
edge of the guide groove
7 . Slide the leg of the com%
bination square until it touches the marked saw tooth
and read the distance between the saw blade and the
guide groove.
Rotate the s aw blade until the marked tooth is jus t
above the table insert at the front.
Slide the combination square along the guide groove
to the marked saw tooth. Measure again the distance
between the s aw blade and the guide groove. The
two measured distances must be identical.
Adjusting:
Loosen the Allen screws 23 at the front and the Allen
screws 33 at the rear under the saw table with the Al%
len key 17 provided. Carefully move the saw blade un%
til it is parallel with the guide groove 7 .
Retighten the screws 23 and 33 .
Distance Indicator of the Parallel Fence
(see Figure )
Place the power tool in the working position.
Swing back the protective hood 5 to the stop.
Slide the parallel fence 2 from the right until it touches
the saw blade.
Checking :
The distance indicator 62 must be aligned with the 0°
mark of the scale 10 .
Adjusting :
Loos en the s crew 71 with a commercially available
Phillips screwdriver and align the indicator along the 0°
mark.
Distance Indicator of the Saw Table
(see Figure )
Set the parallel fence to 33 cm. Loosen the clamping
handle
12 and pull the saw table extension our to the
stop.
Checking :
The distance indicator 63 must indicate on the upper
scale the identical value as the distance indicator 62
indicates.
Adjusting :
Loos en the s crew 72 with a commercially available
Phillips screwdriver and align the distance indicator 63
along the 33 cm mark of the upper scale.
Standard Mitre Angles on the Angle Guide
(see Figure )
On the angle guide, set the standard mitre angle of 0°.
Checking:
Set a combination square to 90° and measure the an%
gle between the guide rail
48 and the profile 49 . The
leg of the combination square must be flush with pro%
file along its entire length.
Adjusting:
Loosen the nut 73 (7 mm) and adjust the stop screw
58 so that when it touches the metal stop 59 , the leg
of the combination square is flush with the stop.
Carefully retighten the nut 73 .
Repeat the steps also for the two 45° mitre angles.
Transport
Before all work on the machine, pull the mains
plug.
For transporting, the electro%tool has the possibility of
securely attaching the parallel fence, the angle guide
and pusher piece. The ring spanner, Allen key and
saw blades can be stored in an orderly manner in the
tool holder
19 .
Lock the yellow safety flap 30 .
Place the power tool in the transport position.
Remove auxiliary parallel fence from the parallel fence.
Position the fences and the angle guide as shown in
Figure
.
Attach the pusher piece 20 with the nut 21 of the tool
holder 19 (see main illustration).
Wrap the mains cable around the cable holders 34 .
Carrying the Power Tool
The power tool should always be carried by two per%
sons to avoid back injuries.
Take hold of it for lifting or for transporting only on the
marked locations under the saw table.
T
U
V
W
X
GTS10_WEU.book Seite 13 Mittwoch, 2. November 2005 2:05 14