Borri B400-010-B (C) Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 38

background image

-1-

1. Safety and EMC Instructions

Please carefully read the following user manual and
safety instructions before installing and using the UPS!

1.1 Installation

★

Check installation instructions before connecting to UPS to the
supply.

★

Condensation may occur if the UPS is transported directly from a
cold to a warm environment. Please allow an acclimatization time
of at least two hours before switching the UPS.

★

Do not install the UPS near a water source or in a damp
environment.

★

Do not install the UPS where it would be exposed to direct
sunlight or near a heat source.

★

Do not connect items of equipment which would overload the
UPS (e.g. laser printers) to the UPS output.

★

Always place cables in such a way so that they are not a trip
hazard.

★

Always make sure the installation is connected to a reliable earth
source.

★

Any additional battery cabinets must be connected to a reliable
earth source.

★

Check after installation, the total earth leakage current including
the UPS and the connected load does not exceed 3.5mA.

★

Do not obstruct the ventilation and air flow of the UPS housing.
Ensure the air vents on the front, side and rear of the UPS are not
blocked. Allow at least 25cm of space on each side.

www.upsdirect.com

«
...
2
3
4
5
6
...
»

Содержание B400-010-B (C)







































Отзывы:

Нет отзывов

Похожие инструкции для B400-010-B (C)

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 24

SmartOnline SU50K3/3INTPM

Бренд: Tripp Lite Страницы: 24

ModularEasy 9PXMEZ6Ki

Бренд: Eaton Страницы: 124

AUPS-2K-A1-ABD1-24V150A

Бренд: La Marche Страницы: 49

NeTYS PE 1000 VA

Бренд: socomec Страницы: 13

Бренд: ACCURAT Страницы: 48

Бренд: ACCURAT Страницы: 20

Бренд: GE Страницы: 11

On-line VH Series

Бренд: GE Страницы: 22

Бренд: GE Страницы: 25

Бренд: GE Страницы: 9

Бренд: GE Страницы: 20

Бренд: GE Страницы: 43

Бренд: GE Страницы: 41

Бренд: GE Страницы: 146

TLE Scalable 150/100 UL S1

Бренд: GE Страницы: 53

LP33 Series 100

Бренд: GE Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды