BorMann 042570, Руководство пользователя, Страница: 5 / 12

5
WWW.BORMANNTOOLS.COM
EN
To install the battery
Hold the drill upright in one hand and the battery in your other hand. While pressing with two fingers on the battery release button, insert the battery until it
clicks into place. Do not use excessive force when inserting the battery. If the battery does not slide in easily, it is not being inserted correctly. It is also possible
that there could be damage to the battery, battery terminals or the drill.
Installing/removing bits and drills
Installing bits/drills
Lock the switch trigger by placing the direction of rotation selector in centre position. Open or close chuck jaws to a point where the opening is slightly larger
than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chuck jaws. Insert drill bit straight into chuck
the full length of the jaws as shown in. Tighten the chuck jaws on the drill bit.
WARNING: Make sure to insert drill bit straight into chuck jaws. Do not insert drill bit into chuck jaws at an angle, this could cause drill bit to be thrown from
drill resulting in possible serious personal injury or damage to the chuck.
Removing bits/drills
Lock the switch trigger by placing rotation selector in centre position. Loosen the chuck jaws from the drill bit. Note: Rotate chuck body in the direction of the
arrow marked. Release to loosen chuck jaws. Do not use a wrench to tighten or loosen the chuck jaws. Remove the drill bit from the chuck jaws.
General hints for drilling
Drilling in all materials
Always use sharp drill bits. Mark the place where you would like the hole to be drilled. Commence with a slow speed to start the hole. Reduce your pressure
on the drill when the drill bit is about to break through the material.
Metal drilling
Support thin material with a piece of scrap wood. Use a center punch to mark the position of the hole. If drilling a large hole, use a small size drill bit first to
establish a pilot hole then use the required large size drill bit. Use only HSS (High Speed Steel) drill bits or those recommended for metal use. When drilling into
iron or steel, use no lubricant but withdraw the drill regularly to assist cooling.
Wood drilling
Mark the place where you want to drill with a punch or a nail. To avoid splintering on breakthrough, either clamp a piece of scrap wood to the back of your work
piece or continue the hole from the back of the wood when the drill bit first breaks through.
FEATURES
Li-ion battery (9)
Advantages of Li-ion batteries :
- Li-ion batteries have a higher capacity/weight ratio (more power for less heavy, more compact, battery)
- No memory effect (capacity loss after several charge/discharge cycles) like other type batteries. (Ni-Cd, Ni-MeH ..).
- Limited self discharge. (also see chapter : Storage)
Keyless chuck (1)
A keyless chuck is included on your drill to allow for easy installation and removal of bits/accessories. The chuck is divided into two parts. The rear is called the
collar and the front is called the body. To open and close the keyless chuck, grasp and hold the collar of the chuck with one hand and rotate the chuck body
with your other hand. The arrows on the chuck indicate in which direction to rotate the chuck body in order to GRIP (tighten) or release (unlock) the drill bit.
WARNING: Do not hold the chuck body with one hand and use power of the drill to tighten or loosen the juck jaws. The chuck body could slip and your hand
could come in contact with a rotating accessory. This could cause an accident resulting in personal injury.
Torque adjustment ring (2)
The drill has a torque adjustment ring. It allows you to select the desired torque depending on the task you have to perform (drill / different types of screw
into different materials). The proper setting depends on the type of material and the size of screw you are using. TO ADJUST TORQUE: Identify the 15+1 torque
indicator settings located on the front of the drill. Rotate adjusting ring (2) to the desired setting. The lower the number, the lower the torque setting. The
higher the number, the higher the torque setting.
Remark:
The torque setting function works only in combination with the screw driver mode.
Function mode selector
-Turn the function mode selector and let the pointer align to the impact mode that selects the impact mode of action.
- Turn the function mode selector and let the pointer align to the drill mode a that selects the drill mode of action.
- Turn the function mode selector and let the pointer align to the screwdriver mode T that selects the screwdriver mode of action.
OΝ/OFF switch (5)
To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. The switch trigger can be locked in the OFF position. This feature helps
reduce the possibility of accidental starting when not in use.