BorMann 022299, Руководство пользователя

Страница: 24 / 30

24
www.BormannTools.com
•
Cutting wheel stop time: After the machine has been switched off, the cutting wheel needs 40 seconds to come to a standstill.
Wait until the cutting wheel has stopped completely, pull the power plug out of the socket outlet, and only then touch the
cutting wheel if necessary.
•
Avoid all contact with the rotating cutting wheel when the machine is in operation.
•
The electric tool must never be used without the PRCD plug supplied with it.
•
Keep water away from electrical parts of the tool and from persons in the work area!
•
If the power plug or the power cable are damaged they must be replaced either by the manufacturer or by a service company
authorized by the manufacturer.
•
To comply with the requirements imposed by the safety regulations, all technical modifications which change the equipment‘s
characteristics (e.g. speed) must be left strictly to the manufacturer.
•
Keep this safety information in a safe place.
Special safety instructions for stone cutting ma - chines
•
Place the stone cutting machine on a level work surface with stable footing before using it. Ensure that there is sufficient room
for freedom of movement.
•
In order to avoid a dust hazard, the machine may only be used in the wet area. This is also mandatory because the diamond
cutting wheel is only suitable for wet cutting.
•
Always fill the tube with water before working.
•
The machine may only be operated in sufficiently ventilated rooms.
•
A ttention! Never leave the motor running in closed or spatially - constrained rooms. The exhaust gases contain toxic carbon
monoxide!
•
As a basic rule, switch on the equipment before material contact.
•
The elevated safety regulations for wet operation apply for this stone cutting machine. All safety measures to prevent elevated
contact voltages must be applied.
•
Electrical cable wires may not come into contact with water or water vapour.
•
Before commencing work, check the equipment and mains cable for damage.
•
Check whether the moving parts function faultlessly and do not jam and make sure that no parts are damaged.
•
The mains voltage must match the specifications on the type plate of the machine.
•
Only use approved extension cables for use out - doors.
•
When using a cable reel, completely unwind the cable in order to prevent the cable from heating up.
•
When working outside, the electrical outlet must be equipped with a residual current circuit breaker.
•
Observe the motor and diamond cutting wheel direction of rotation.
•
Only cut one workpiece at a time.
•
The cut path must be kept of obstacles above and below.
•
Make sure that you can remove cut workpieces from the cutting wheel from the side in order to ensure that avoid becoming
entangled.
•
Use a push rod in order to guide the workpiece safely past the cutting wheel.
•
Only work with diamond cutting wheels which are exclusively suitable for wet cutting.
•
Use diamond cutting wheels which are the correct size.
•
Keep your hands, fingers and arms away from the rotating cutting wheel. Always maintain sufficient clearance from the diamond
cutting wheel.
•
Replace faulty diamond cutting wheels immediately. Deformed or cracked cutting wheels may not be used.
•
Only use diamond cutting wheels recommended by the manufacturer which conform to EN13236. The use of any type of saw
blades is prohibited.
•
Make sure that a suitable diamond cutting wheel for the material to be cut is selected.
•
Do not use the stone cutting machine without safety equipment.
•
Always switch off the machine and pull out the mains plug for the correction of errors or removal of jammed workpieces. Only
remove the jammed workpiece after doing so.
•
Protect the diamond cutting wheel from impact and jarring. Do not subject it to any lateral pressure.
•
Do not stress the device to the extent that it is brought to a stop.
•
Wear suitable personal protective equipment (PPE).
-
Hearing protection to avoid the risk of becoming hearing impaired.
Attention! Noise can be harmful to the health. If the permissible noise level of 80 dB(A) is exceeded, hearing protection must
be worn.
-
Respiratory protection to avoid the risk of inhaling harmful dust.
-
Eye protection to avoid the risk of injuring the eyes.
-
Gloves are recommended when handling raw materials and shoes with non - slip soles when working outdoors.
•
Diamond cutting wheels must always be carried in a container whenever practical.
•
This machine may only be operated by persons who are familiar with stone cutting machines.
•
Errors in the machine, including all covers and protective devices must be reported to the person responsible for safety as soon