BorMann 018988, Руководство пользователя

Страница: 3 / 15

3
www.BormannTools.com
6. Use heavy leather gloves when handling wire rope. Do not let wire rope slide through your hands.
7. Never winch with less than 5 turns of wire rope around the winch drum since the wire rope end fastener may NOT
withstand full load.
8. Never put your finger through the hook. If your finger should become trapped in the hook, you could lose your finger.
ALWAYS USE THE HAND SAVER when guiding the wire rope in or out.
9. NEVER HOOK THE WIRE ROPE BACK ONTO ITSELF because you could damage the wire rope. Use a nylon sling.
10. It is a good idea to lay a heavy blanket or jacket over the wire rope near the hook end when pulling heavy loads. If a wire
rope failure should occur, the cloth will act as a damper and help prevent the rope from whipping.
11. AVOID CONTINUOUS PULLS FROM EXTREME ANGLES as this will cause the wire rope to pile up on one end of the drum.
This can jam the wire rope in the winch, causing damage to the rope or the winch.
12. NEVER OBSCURE THE WARNING INSTRUCTION.
13. Always operate winch with an unobstructed view of the winching
14. Equipment such as tackle, hooks, pulley blocks, straps, etc. should be sized to the winching task and should be periodically
inspected for damage that could reduce their strength.
15. NEVER RELEASE FREE SPOOL CLUTCH WHEN THERE IS A LOAD ON THE WINCH.
16. NEVER WORK ON OR AROUND THE WINCH DRUM WHEN WINCH IS UNDER LOAD.
17. DO NOT OPERATE WINCH WHEN UNDER THE INFLUENCE OF DRUGS, ALCOHOL OR MEDICATION.
18. ALWAYS DISCONNECT WINCH POWER LEADS TO BATTERY BEFORE WORKING IN OR AROUND THE WINCH DRUM so that
the winch cannot be turned on accidentally.
19. When moving a load, slowly take up the wire rope slack until it becomes taut. Stop, recheck all winching connections. Be
sure the hook is properly seated. If a nylon sling is used, check the attachment to the load.
20. When using your winch to move a load, place the vehicle transmission in neutral, set vehicle brake, and chock all wheels.
21. DO NOT USE THE WINCH TO HOLD LOADS IN PLACE. Use other means of securing loads such as tie down straps.
22. USE ONLY FACTORY APPROVED SWITCHES, REMOTE CONTROLS ACCESSORIES. Use of non-factory approved components
may cause injury or property damage.
23. DO NOT MACHINE OR WELD ANY PART OF THE WINCH. Such alterations may weaken the structural integrity of the winch.
24. DO NOT CONNECT WINCH TO EITHER 110V AC HOUSE CURRENT OR 220V MAINS AS WINCH BURNOUT OR FATAL SHOCK
MAY OCCUR.
25. Never allow shock loads to be applied to winch or wire rope.
26. Use caution when pulling or lowering a load up and down a ramp or incline. Keep people, pets and property clear of the
path of the load.
27. The switch assembly must be kept free of dirt and moisture to ensure safe operation.
28. To prevent unauthorized use of the winch, remove pendant control and store in a clean dry area such as the glove box.
Installation
Caution: No part of the vehicle (skid plates, wiring, auxiliary lights, Tires, etc.) should impede the operation of your winch.
When mounting, check all vehicle and winch parts for free operation. Be sure that the winch mounting location does not
significantly reduce ground clearance.
Step (1)
Mount the winch to a firm base. Be sure that your structural support is strong enough to support the rated pulling forces of
the winch.
Step (2)
While mounting attitude is at your discretion, always remember that your winch is to be operated with the wire rope in an
under wound orientation on the wire rope drum. Your winch is designed to ROPE IN and ROPE OUT in one direction. DO NOT
attempt to reverse the operation of winch.
Warning: Batteries contain gasses which are flammable and explosive Wear eye protection during installation and remove
all metal jewelry. Do not lean over battery while making connections.