bonitron M3645 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 56

background image

User’s Manual

39

This  can  also  mean  that  the  regen  is  too  small  to  handle  the  braking
requirements.  Make sure the regen is not operating in the current limit during
braking.
This fault may occur if the regen is connected to multiple drives, with blocking
diodes  between  each  drive  ant  the  regen.  This  topology  is  not  supported.
Please contact Bonitron for possible alternative common bus solutions.

5.3.8.

D

IFFERENTIAL

O

VERVOLTAGE

Differential overvoltage can be caused by the same reasons as the DC
overvoltage. Refer to Section 5.3.7.

5.3.9.

S

YNC

L

OSS

Ensure that the overcurrent devices on the incoming AC line are intact.
Ensure that the AC source is properly sized for the application.  "Soft" or high
impedance sources can have significant voltage distortion that can cause the
regen to lose sync.  Most drives will not be affected by this distortion.  You
can check for voltage distortion on the incoming AC line with an oscilloscope
with appropriate leads.  It will be important to be watching the AC line when
the Sync Loss fault occurs, as the distortion may not be on the line all the
time, especially when it is not loaded.
If a sync loss fault is listed in the fault log in conjunction with a Precharge Not
Complete fault, this indicates that control power to the unit has been reset.
No actual sync loss condition has occurred.

5.3.10.

IGBT

D

RIVER

This fault can be reset the M3645 by toggling the Enable input. (4.5.2)
If the fault cannot be cleared, or occurs frequently, the unit may be damaged.
Contact Bonitron for assistance.
If two M3645 units are operated in parallel, IGBT faults may indicate that the
parallel combination is undersized for the application.

5.3.11.

P

HASE

O

VERCURRENT

This fault can be cleared by toggling the enable input. (4.5.2)
If it occurs frequently, there may be a voltage imbalance on the incoming AC
line. Ensure that the incoming line voltages are within 3% of each other.

5.3.12.

P

HASE

L

OSS

This fault typically means that the incoming power overcurrent devices or
fuses are blown.
Power the regen down and check all fuses and that AC voltage is present at
the terminals of the regen.

5.3.13.

DC

U

NDERVOLTAGE

This may indicate that overcurrent devices in the DC link may have opened.
Check  the  AC  and  DC  voltages  with  an  external  voltmeter  and  make  sure
they are within specification.
If  the  voltages  are  correct,  and  the  fault  will  not  clear,  contact  Bonitron  for
assistance.

5.3.14.

R

EGEN

P

OWER

-O

N

/P

RECHARGE

N

OT

C

OMPLETE

This fault is expected to occur every time the unit powers on. It should clear
automatically within ten seconds.

«
...
37
38
39
40
41
...
»

Содержание M3645

























































Отзывы:

Нет отзывов

Похожие инструкции для M3645

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: IBM Страницы: 105

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 26

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды