bonitron M3645 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 56

background image

User’s Manual

37

5.

M

AINTENANCE AND

T

ROUBLESHOOTING

Repairs or modifications to this equipment are to be performed by Bonitron approved
personnel only. Any repair or modification to this equipment by personnel not approved
by Bonitron will void any warranty remaining on this unit.

5.1.

P

ERIODIC

T

ESTING

There are no requirements for periodic testing of these units. It may be beneficial to
repeat start-up procedures and checks when performing routine maintenance.

5.2.

M

AINTENANCE

I

TEMS

Check the fan periodically for debris, and blow out with an air hose if it has become
obstructed or not running at full capacity.

Power should not be applied when

blowing dust and debris out of unit

.

5.3.

T

ROUBLESHOOTING

CAUTION!

There are no user serviceable parts within the M3645 regen unit. If you
are still experiencing problems after you have reviewed this whole section,
you may contact Bonitron for additional assistance at (615) 244-2825.

5.3.1.

POWER

LED

IS NOT ON

,

OR

D

IGITAL

D

ISPLAY IS NOT ACTIVE

:



Check AC input voltage at terminals. Voltage should be within range
specified in Table 2-1 for your unit. If the power light will not come on,
check any overcurrent devices or disconnects upstream of the regen.



If the power lamp will not come on, it is likely that the regen is damaged
and needs to be repaired.

5.3.2.

READY

OUTPUT WILL NOT CLOSE

The  Ready  output  indicates  that  the  module  is  enabled  and  in  a  ready
condition.  When the power is applied to the module, the Ready output will
normally close after a startup delay of approximately 2 seconds.  Thereafter,
the  Ready  output  should  be  closed,  indicating  that  the  system  is  ready  to
operate.    If  the  Ready  output  fails  to  close,  one  of  several  faults  may  be
indicated.



Make sure the Power LED is on.
If the Fault LED is blinking, refer to Table 4-1

, “Blink Codes” to determine

which fault is active, or look at the digital display.



If the Fault LED is on solid, the "Enable" input is not activated.

5.3.3.

U

NIT WILL NOT RESPOND TO

ENABLE

COMMAND



Confirm that 24V is present between TB2-2 and TB2-4 (see Figure 3-6).



If the internal 24V supply is being used, confirm that a jumper is present
between TB2-4 and TB2-5 (0).

5.3.4.

D

RIVE TRIPS ON

DC

B

US

O

VERVOLTAGE DURING BRAKING

If the attached drive trips, it typically indicates the regen is not operating.
There are some simple things that can determine the cause.



Make sure the regen has power and is enabled. The Ready output will
close if the unit is ready to operate. (4.5.2)

«
...
35
36
37
38
39
...
»

Содержание M3645

























































Отзывы:

Нет отзывов

Похожие инструкции для M3645

Бренд: H3C Страницы: 57

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 26

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 20

INDUSTRY PAN9028

Бренд: Panasonic Страницы: 34

Бренд: Eaton Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды