Bonex aquaProp Скачать руководство пользователя страница 5

 
aquaProp–SCOOTER 

Instruction  for  use 

 

Version: 

SG 

2015-11 

 

 

 

Page 5 

 

 

 

5. Brief instruction for the aquaProp-Scooter 

1.  Read the manual carefully before operating the device! 

2.  Storage: 
 

  Main switch 

„OFF“

 (otherwise total damage of battery is possible!) 

  Place scooter with “Shroud“ down on flat ground or store it with scooter stillage 

  Place scooter in shadow (sun heats up the interior)! 

  Remove Tube O-rings before prolonged storage! 

  Recharge battery before prolonged storage!

 

 
3.  Transport (per parcel service etc.): 
 

  Remove battery plug 

  Check the reliable fit of the battery inside the scooter! 

  Transport the scooter only in the original transport box or in the additional transport bag fitted in a carton with 

foam! 

4.  Starting up: 

 

  Charge battery! 

  Check the battery connector cable for proper connection to battery! 

  Remove all dirt (hair, dust, greenery, etc.) from the seal seats! 

  Lightly grease the O-rings of the housing! 

 

Housing upper part inside lightly grease the sealing seat!

 

  Assemble the saltwater trim weights, if necessary! 

 

Mount the housing top in the right driving position (1-hand / 2-hand operation). For this purpose, put the 
arrow on the first "OPEN" position on the back of the rear with shroud, and rotate it to the arrow "CLOSE". 
Only in this position, the scooter is properly closed. 

Incorrect installation can lead to leaks!

 

  Don’t place the scooter in direct sun (battery can be damaged)! 

 

If desired, a scooter insurance to be completed within 14 days after delivery of the scooter.

 

5.  After-Treatment: 
 

  Switch off the scooter on the step switch! 

  Rinse the scooter after each salt water use thoroughly! 

  After saltwater use of the scooter, disassemble the propeller! 

Rinse the slide ring sealing with fresh water from the outside on the housing bottom part! 

Do not clean slide ring sealing mechanically! 

  Disconnect the battery connector! 

  Inspect the inside! 

6.  Maintenance: 
 

  Clean the rear part occasional and lubricate with silicone spray! 

  Check  Tube  O-rings  after  6  month  and  change  them  at  least  once  a  year  (long  storage  will  cause 

deformation of the O-rings)! 

  In salt water use once a month grease the O-Ring of the slide ring sealing! 

 

Every 2 years is recommended an inspection by an authorized workshop!

 

Please heed the above points, they provide smooth operation and continued enjoyment of the aquaProp scooters 
safe! AquaProp can perform the regular maintenance for you.

 

Содержание aquaProp




















Отзывы: