manualshive.com logo in svg

Bonart KRUUSE-SP1, Инструкция по эксплуатации

Поделиться
Скачать
Bonart KRUUSE-SP1 Скачать руководство пользователя страница 19

 

- 18 - 

 

7.

 

Micro-Motor    Socket 

The micro-motor socket is where you connect the micro-motor to the main unit.    It is located 

on the back of the main unit at the bottom left. 

 

8.

 

Footswitch Socket 

The foot switch socket is where you connect the foot switch to the main unit.    It is located 

next to the water hose input on the back of the main unit. 

 

9.

 

Water hose input connector

 

The water hose input connector is the contact point for the water tube and the main water 

supply line.    Use either a male or female quick connect to connect the water tube to the water 

supply.    The KRUUSE-SP1 comes with a male quick connect attached to the water tube. 

 

10.

 

Power cord socket 

The power cord socket is where you connect the power cord to the main unit. 

 

11.

 

Forward / Reverse switch 

The Forward/Reverse switch allows you to control the direction of the micro-motor.    It is 

located on the back of the main unit.   

Содержание KRUUSE-SP1

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды