manualshive.com logo in svg

Bonart KRUUSE-SP1, Инструкция по эксплуатации

Поделиться
Скачать
Bonart KRUUSE-SP1 Скачать руководство пользователя страница 18

 

- 17 - 

The hand piece will heat up when used due to the power generated by the main unit.   

Therefore it is necessary to cool the hand piece by ensuring that an adequate amount of water 

flows through the hand piece. 

 

CAUTION

：

Make sure that new insert is firmly seated. 

CAUTION: Do not depress the footswitch when there is no insert installed.    Doing so 

will cause the hand piece to melt! 

NOTE

：

The KRUUSE-SP1 is a stand-alone unit and is now only available in 25Khz.   

Please do not use 30Khz inserts with the hand piece. 

 

3.

 

Power button (ON/OFF) 

The power button is used to turn the KRUUSE-SP1 main unit on and off.    When the power is 

on, the LED indicator should be lit.    When turned off, the LED power indicator should not be 

lit. 

 

Do not depress the foot switch while turning on the KRUUSE-SP1.

 

 

4.

 

Micro-motor (Mode) button 

The micro-motor (Mode) button is used to switch between polishing and scaling 
mode.    When pushed, the LED indicator should be lit, indicating that the system 
is operating in

 polishing 

mode.    Under polishing mode, the micro-motor is 

engaged.    To return to 

scaling 

mode, push the button again. 

 

5.

 

Water control knob 

The water control knob allows you to control the amount of water that flows through the hand 
piece.    If turned clockwise, the amount of water will decrease.    If turned counter-clockwise, 
the  amount  of  water  will  increase.    Please  note  that  water  is  necessary  to  cool  the  tip  and 
prevent  overheating  so  it  is  necessary  to  ensure  that  an  adequate  amount  of  water  flows 
through the hand piece while operating the device.    The larger the water stream, the lower the 
temperature, and vice versa. 

WARNING

：

Do  not  turn  the  water  knob  counter-clockwise  more  than  three  full  turns.   

Doing so will damage the internal water line needle. 

WARNING

：

If needed, gently adjust the water control knob to prevent any serious 

damages to the water valve. 

 
6.

 

Power control knob 

The Power Control Knob allows you to control the power intensity.    When turned clockwise, 
the power intensity increases.    When turned counter-clockwise, the power intensity decreases. 

Содержание KRUUSE-SP1

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды