BodyCraft MINI-XPress 7351 Скачать руководство пользователя

Страница: 8 / 11

STEP 3

63a

1.Attach the Seat Back Adjuster (10) to the Upright (3) using one 3/8" X 3" Hex Bolt (62),

two 3/8" Washers (74) and one 3/8" Nut (77). Do not tighten completely, Leave the bolt

loose, just enough to let the Seat Back Adjuster (10) pivot freely.

2.Attach the Pop Pin (58) for the Seat Back Adjuster (10) to the Upright (3). Slide two Metal

Hinges (22) onto each end of the round top of Seat Back Adjuster (10), then attach the

Back Pad (32) to the Metal Hinges (22) using two 3/8" X 1" Hex Bolts (65), and two 3/8"

Washers (74). Insert the Foam Roller Holder (6) into the hole in the Seat Back Adjuster.

Moisten the inside holes of two Foam Pads (28) with water and slide onto each end of the

Foam Roller Holder (6). Cap the Foam Roller Holder (6) with two 1" Id Foam Round Plug

(49). Lock the Foam Roller Holder (6) into place with the pre-installed Set Screw (72) on

the Seat Back Adjuster (10).

3.Attach the Seat Pad (33) to the Seat Adjuster (9) using two 3/8"X 2-3/4" Hex Bolts (63a)

and two 3/8' Washers (74). Cap the front and rear of the Seat Adjuster (9) with two 50mm

SQ. Plugs (48). Pull the pre-installed Pop Pin (57) to let the Seat Adjuster into the Seat

Frame of Base.

Tighten all bolts and nuts.

Содержание MINI-XPress 7351











