BobsCNC RP9 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 45

background image

17

1. Assemble each of the threaded rods into the larger coupler slots.
2. Connect the coupler halves with 4 M3 x20 screws and nuts.
3. Only snug up the screws, they will be tightened in a later step.

6. Thread both of the coupler assemblies into the threaded inserts on the Y assembly. The
coupler halves may need to be removed to get the threads started through the inserts on
the Y assembly.

«
...
15
16
17
18
19
...
»

Содержание RP9














































Отзывы:

Нет отзывов

Похожие инструкции для RP9

Бренд: DataCard Страницы: 7

Бренд: Canon Страницы: 4

Бренд: Make Mendel Страницы: 29

201021 - P 330N Photo Printer

Бренд: Olympus Страницы: 79

Бренд: A&D Страницы: 24

Бренд: Oki Страницы: 32

Suprasetter 106

Бренд: HEIDELBERG Страницы: 91

EasyCoder PL-Series

Бренд: Intermec Страницы: 220

Бренд: Liene Страницы: 64

Бренд: OKIDATA Страницы: 158

Бренд: Citizen Страницы: 255

imageRUNNER ADVANCE DX C5870i

Бренд: Canon Страницы: 100

imageRUNNER ADVANCE C356iF

Бренд: Canon Страницы: 96

imageRUNNER ADVANCE C350 series

Бренд: Canon Страницы: 1173

imageRUNNER ADVANCE DX 6870i

Бренд: Canon Страницы: 100

imageRUNNER ADVANCE 715iFZ III

Бренд: Canon Страницы: 92

ImageRUNNER C1538iF

Бренд: Canon Страницы: 120

imageRUNNER ADVANCE DX 717iFZ

Бренд: Canon Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды