Bobrick AirCraft B-701 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 66

Bobrick AirCraft B-701 Скачать руководство пользователя страница 55

Page 5

Recommended Mounting Heights:

Distance from floor to bottom mounting screw holes of mounting
base.
Men's Washrooms  .......................................................  45-1/4'' (1150mm)
Women's Washrooms ..................................................  43-1/4'' (1100mm)
Children's Washrooms, ages 3-9  ................................  31-1/4'' (795mm)
Children's Washrooms, ages 9-12  ..............................  35-1/4'' (895mm)
Children's Washrooms, ages 12-15  ............................  39-1/4'' (995mm)
Children's Washrooms, ages 15-18  ............................  43-1/4'' (1100mm)
For the Handicapped  ...................................................  37-1/4'' (945mm)

Place  mounting  base  on  wall  at  the  desired  location  of  the  installed  dryer.  See
recommended mounting heights.

Use  the  mounting  base  or  the  template  provided  with  dryer  to  mark  location  of  three
mounting screw holes and access hole for electrical wiring (if electrical supply is concealed
in wall and will enter dryer from back through mounting base).

NOTE

: Surface mounted electrical supply (line cord) is attached to dryer through hole in air

inlet/outlet grille in lower left corner.

Drill three holes for #10 (M4.8) diameter mounting bolts or screws (not furnished by
Bobrick).

For masonry walls provide three #10 expansion shields or anchors, then secure with three
#10 (M4.8) sheet-metal screws (not furnished). For plaster or dry wall construction, provide
concealed backing to comply with local building codes and secure with three #10 (M4.8)
round-head sheet-metal screws, or 3/16'' (5mm) toggle bolts (not furnished).

NOTE

: Use 1-3/4'' (45mm) screws.

Fasten mounting base securely to wall.

WARNING:

TURN ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL

CONNECTIONS.

DRYER MUST BE GROUNDED (EARTHED).

ELECTRICAL CONNECTION

FOR  PROPER  ELECTRICAL  CONNECTIONS,  CHECK  LOCAL  BUILDING  CODE.    UNIT
MUST  BE  INSTALLED  BY  A  QUALIFIED  LICENSED  ELECTRICIAN.    WARNING;  TURN
ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL CONNENTIONS.

Connect dryer to nearest distribution panel. Use wire as required by local electrical code. In
the United States and Canada use #12 wire or larger.

A  fused  means  for  disconnection  in  all  poles  must  be  provided  in  the  fixed  wiring  in
accordance with the wiring rules.

For Model B-740 115V and B-748 115V Dryers:

Connect ground (earth) wire to ground

(earth) terminal on the mounting base marked

. Connect the black or Hot wire to terminal

«
...
53
54
55
56
57
...
»

Содержание AirCraft B-701



































































Отзывы:

Нет отзывов