manualshive.com logo in svg

Bobrick AirCraft B-701, Руководство по устранению неисправностей и информации, Страница: 26 / 66

Поделиться
Скачать
Bobrick AirCraft B-701 Скачать руководство пользователя страница 26

Page 20 

 

Hair dryer. 
 

Men’s Dressing Rooms  .........................................................  72'' (183cm) 
Women’s Dressing Rooms  ....................................................  64'' (163cm) 
Children’s Dressing Rooms, ages 3-9  ...................................  45'' (114cm) 
Children’s Dressing Rooms, ages 9-12  .................................  52'' (132cm) 
Children’s Dressing Rooms, ages 12-15  ...............................  58'' (147cm) 
Children’s Dressing Rooms, ages 15-18  ...............................  63'' (160cm) 
Drill  four  holes  for  1/4"  (6.4mm)  diameter  mounting  bolts  or  screws  (not  furnished  by 
Bobrick). 
Fasten mounting base securely to wall. 
 
Place  mounting  base  on  wall  at  the  desired  location  of  the  installed  dryer.  See 
recommended  mounting  heights  above.  Use  the  mounting  base  or  the  template  provided 
with  dryer  to  mark  location  of  four  mounting  screw  holes  and  hole  for  electrical  wiring  if 
electrical supply is concealed in wall and will enter dryer from back through mounting base. 

NOTE: 

Surface-mounted  electrical  supply  is  attached  to  mounting  base  in  lower  right 

corner. Flange of mounting base and bottom of cover are notched in lower right corner to 
accommodate connection of electrical conduit. 

 

WARNING: 

TURN ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL 

CONNECTIONS. 

DRYER MUST BE GROUNDED (EARTHED). 

 
ELECTRICAL CONNECTION. 
 

FOR  PROPER  ELECTRICAL  CONNECTIONS,  CHECK  LOCAL  BUILDING  CODE.    UNIT 
MUST  BE  ISTALLED  BY  A  QUALIFIED  LICENSED  ELECTRICIAN,  WARNING:  TURN 
ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL CONNENTIONS. 
 
Connect dryer to nearest distribution panel. Use wire as required by local electrical code. In 
the United States and Canada use No. 12 wire or larger. 
 
Wiring Instructions: 
 
A  fused  means  for  disconnection  in  all  poles  must  be  provided  in  the  fixed  wiring  in 
accordance with the wiring rules. 
 

For 115 Volt Dryers: 

Connect ground (earthed) wire to ground (earthed) terminal marked 

,  the  black  or  Hot  wire  to  terminal  marked  L1  and  neutral  or  white  wire  to  terminal 

marked N.  
 

DEDICATED LINE IS REQUIRED FOR EACH 115 VOLT DRYER. 

 

For  208

–240  Volt  Dryers: 

Connect  ground  (earthed)  wire  to  ground  (earthed)  terminal 

marked 

 and the 208-240 Volt wires to terminals marked L(L1) and N (L2). 

 
Secure electrical wire in strain relief clamp provided on mounting base. 
 
 
 
 

Содержание AirCraft B-701



































































Отзывы:

Нет отзывов