Bobrick AirCraft B-701 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 66

Bobrick AirCraft B-701 Скачать руководство пользователя страница 29

Page 23

Provide  framed  opening  in  wall  13-3/4''  wide  x  9-1/2''  high  x  3-3/4''  deep  (349  x  241  x
95mm)  at  the  desired  location  of  the  installed  dryer.  See  recommended  mounting  heights
above.
Frame the opening as shown in diagram to support recessed mounting box.
Place  the  recessed  mounting  box  in  wall  and  cut  an  opening  in  the  framing  to  allow
clearance for electrical conduit and fittings at one of the three conduit knockout locations.
Fasten recessed mounting box to framing with minimum of four No. 10 (4.8mm) sheet metal
screws  (not  furnished  by  Bobrick).  Make  sure  flanges  of  mounting  box  are  completely  flat
against  finished  wall  surface.  If  necessary,  use  shims  or  spacers  between  mounting  box
and framed wall opening to prevent distortion to box as it is fastened to framing.
Install  electrical  conduit  from  nearest  distribution  panel  to  recessed  mounting  box.  Attach
conduit fittings to mounting box. Use wire as required by local electrical code. In the United
States and Canada use No. 12 wire or larger. Allow a minimum of 24'' (610mm) of wire to
remain in recessed mounting box for connection to dryer terminals.

INSTALLATION OF ALUMINUM BASE UNIT INTO RECESSED MOUNTING BOX.

Start installation of aluminum base unit into recessed mounting box by removing cover. To
loosen  two  cover  bolts,  insert  Allen  wrench,  provided  with  dryer,  into  holes  located  on
bottom edge of cover. Make sure wrench fits into head of cover bolts and turn CLOCKWISE
until  bolts  stop  turning.  When  both  cover  bolts  are  screwed  in  all  the  way,  cover  can  be
removed.
To  remove  cover,  place  a  hand  on  each  side  of  cover  and  push  up  toward  top  of  dryer
releasing cover from studs at top of aluminum base unit. Lift cover off base unit by pulling
forward at the bottom and upward at the same time.
Insert aluminum base unit into recessed mounting box and fasten to top and bottom flanges
of mounting box with the four 1/4-20 UNC (MG-1) screws provided.

WARNING:

TURN ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL

CONNECTIONS.

DRYER MUST BE GROUNDED (EARTHED).

ELECTRICAL CONNECTION.

FOR PROPER ELECTRICAL CONNECTIONS, CHECK LOCAL BUILDING CODEE.  UNIT
MUST  BE  INSTALLED  BY  A  QUALIFIED  LICENSED  ELECTRICIAN.    WARNING:  TURN
ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL CONNECTIONS.

Wiring Instructions:

A  fused  means  for  disconnection  in  all  poles  must  be  provided  in  the  fixed  wiring  in
accordance with the wiring rules.

For 115 Volt Dryers:

Connect ground (earthed) wire to ground (earthed) terminal marked

, the black or Hot wire to terminal marked L1 and neutral or white wire to terminal

marked N.

«
...
27
28
29
30
31
...
»

Содержание AirCraft B-701



































































Отзывы:

Нет отзывов