background image

2

SPEKTRUM DX6e • TRANSMITTER INSTRUCTION MANUAL

EN

WARNING:

 Read the ENTIRE instruction manual to become familiar with the features of the product before operating. 

Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. 

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. 
Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This 
product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible compo-
nents or augment product in any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation 
and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in 
order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS 

Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, 

LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products 
claiming compatibility with DSM or Spektrum technology.

NOTICE: 

This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles and aircraft. Horizon Hobby 

disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.

Age Recommendation: Not for Children under 14 years. This is not a toy.

Warranty Registration

Visit 

spektrumrc.com

 today to register your product.

NOTICE:

 

While DSMX allows you to use more than 40 transmitters simultaneously, when using DSM2 receivers, DSMX receivers in 

DSM2 mode or transmitters in DSM2 mode, do not use more than 40 transmitters simultaneously.

General Notes 

•  Models are hazardous when operated and maintained incorrectly. 
•  Always install and operate a radio control system correctly. 
•  Always pilot a model so the model is kept under control in all 

conditions. 

•  Please seek help from an experienced pilot or your local 

hobby store. 

•  Contact local or regional modeling organizations for guidance 

and instructions about fl ying in your area. 

•  When working with a model, always power on the transmitter 

fi rst and power off the transmitter last. 

•  After a model is bound to a transmitter and the model is set 

up in the transmitter, always bind the model to the transmitter 
again to establish failsafe settings. 

Pilot Safety

•  Always make sure all batteries are fully charged before fl ying. 
•  Time fl ights so you can fl y safely within the time allotted by 

your battery.

•  Perform a range check of the transmitter and the model 

before fl ying the model. 

•  Make sure all control surfaces correctly respond to transmitter 

controls before fl ying. 

•  Do NOT fl y a model near spectators, parking areas or any 

other area that could result in injury to people or damage to 
property.

•  Do NOT fl y during adverse weather conditions. Poor visibility, 

wind, moisture and ice can cause pilot disorientation and/or 
loss of control of a model. 

•  When a fl ying model does not respond correctly to controls, 

land the model and correct the cause of the problem.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date 
product literature, visit horizonhobby.com and click on the support tab for this product.

Meaning of Special Language

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE:

 Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

CAUTION:

 Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

WARNING:

 Procedures, which if not properly followed, create the probability of property damage, collateral damage and serious injury 

OR create a high probability of superfi cial injury.

Содержание DX6E














































Отзывы: