Mixer Manual 2017.indd • May 31, 2017
Page 12
BN Products - USA
Paddles for the BN Power Mixers
BNRA0315
1/2” Drill Chuck
BNR001 -
Specify Diameter
120 mm (4.75”) or 140 mm (5.50”) or 160 mm (6.30”) • Overall length: 60 cm (24”) • Designed for
plasters, adhesive mortars, mortars, tile adhesives and fillers, best for sticky and viscous materials.
• Material Flow: Bottom to Top • Connection: M14 x 2 male threads
BNR002-57
Diameter: 57 mm (2.25”) • Overall length: 13.5” • Designed for paints, lacquers, thin coatings, and
ready-mix plaster. • Material Flow: Top to Bottom • Connection: 5/16” hex shank
BNR003-
Specify Diameter
120 mm (4.75”) or 140 mm (5.50”) or 160 mm (6.30”) • Overall length: 60 cm (24”) • Designed for
concrete, mortars, plasters, heat-insulating plasters, and epoxy resin with sand, best for heavy and
high viscosity materials. • Material Flow: Top to Bottom • Connection: M14 x 2 male threads
BNR004-
Specify Diameter
120 mm (4.75”) or 140 mm (5.50”) • Overall length: 60 cm (24”) • Designed for thinset, tile ad-
hesive, grout, adhesive mortars, ready-mix mortars, and pointing mortars, and fillers, best for
small volumes on high speed mixers. • Material Flow: Bottom to Top • Connection: M14 x 2 male
threads
BNR005-120
Diameter: 120 mm (4.75”) • Overall length: 60 cm (24”) • Designed for plasters, adhesive mortars,
tile adhesive and fillers, best for sticky and viscous materials. • Material Flow: Bottom to Top •
Connection: M14 x 2 male threads
BNR006-100
Diameter: 100 mm (3.875”) • Overall length: 60 cm (24”) • Designed for paints, lacquers, glazings,
primers, and paste, best for small volumes of low viscosity materials • Recommended to use on
BNR6169. • Material Flow: Top to Bottom • Connection: M14 x 2 male threads
BNR007-140
Diameter: 140mm (5-1/2”) • This is a special paddle that fits the BNR7000 TwinMaster Mixer™. It
turns in two directions at the same time.
BNR008-120K
Paddles sold in
pairs
left & right
Diameter: 120 mm (4.75”) Overall length: 60 cm (24”) • Designed for concrete, cement, mortars,
and grouts with aggregate less than 3/8” diameter. Also for gypsum lime plaster, fibrated aluminum
roof coatings and paints. Not for highly viscous materials. • Material Flow: Top to Bottom • Con-
nection: 13 mm or ½” Hex Shank, for BNR6402K mixer.
BNR009-Specify
Diameter
120 mm (4.75”) or 140 mm (5.50”) • Overall length: 60 cm (24”) • Designed for fillers, bitumen
coatings, joint cement, epoxy-resin compounds, and grouting compounds, best for prevention of
lump formation and lessens adding air into the mixture. Mixture flow is parallel. • Connection:
M14 x 2 male threads
BNR010-
Specify Diameter
120 mm (4.75”) or 140 mm (5.50”) • Overall length: 60 cm (24”) • Designed for gypsum-lime plas-
ter, fibrated aluminum roof coatings, and paints. This paddle can be disassembled in two pieces
and fit into a carrying case. • Material Flow: Top to Bottom • Connection: M14 x 2 male thread
