background image

 Page |  5 

Fu n ctio n s  a n d  Ap p lica tio n s

This section describes the functions, applications, service environm ent and other aspects 
of the Cutting Edge Saw. The Cutting Edge Saw is a power tool developed for fast and ef-

ficient cutting of various ferrous and non-ferrous materials. This multipurpose tool can be 

used by a variety of contractors however the primary design was for flush cutting or free 

cutting reinforcing bars, coil rod and all-threaded rod used in the construction industry.

Ap p lica tio n  o f th e  To o l

 - Actual areas of application the Cutting Edge Saw is used for 

are as follows:

The BNCE-30-24V can cut up to 1” grade 60 rebar (reinforcing bars, up to 3/5” I.D pipe, 

1” O.D. copper water pipe, 1” O.D. tubing, 3/4” EMT conduit, 1” square steel tubing and 

bar, up to 1”water pipe sch40 and schedule 80, up to 1-1/8” O.D all-thread rod.

Rules of Use and Storage - To use the tool to its fullest performance, the user is required 

to be fully fam iliar with the saw itself, the cutting blades, and storage procedures upon 
com pletion of work. 

Specification

The power tool is a multipurpose saw with an enclosed guard and flush cutting capabili

-

ties. The specifications of the main unit are as follows.

S ta n d a rd  Bla d e : 

(Best for Ferrous Metals)

Supplied with (2) each 5” 127 m m  Blade diam eter × 1.6m m  thickness, 30  teeth. The m axi-
m um  blade RPM is 20 0 0 . The blade replacem ent num ber is: RB-BNCE-30

Op e ra tio n

• 

Checking and Preparation of Working Environm ent

• 

Check the following before using the Cutting Edge Saw. Always observe the instruc-
tions and prohibited item s.

• 

Checking of weather conditions, do not use in the rain or snow 

!DANGER: The Cutting Edge is not a waterproof power tool. If it becom es 
wet, the power source system  m ay becom e faulty or the operator m ay get 
an electric shock. Therefore, when it is raining or snowing, never operate 
this saw outdoors, on top of buildings or under roofs where rain or snow 
enters freely. Do not use where water accum ulates or where water splashes.

Содержание BNCE-30-24V

















Отзывы: