BMW 66 20 0 007 031 Скачать руководство пользователя страница 3

 

EN/3

 

Retrofit / Installation kit No. 66 20 0 007 031
Installation Instructions No. 01 29 0 137 628

Issue date: 02.2002

 

Important information

 

The retrofit kit is for use within the BMW dealership organisation only.

 

Target group

 

The target group for these installation instructions is specialist personnel trained on BMW cars 
with specialist knowledge of body electrical systems.
All work is to be carried out using current BMW
- Repair manuals (see Technical Information System),
- Circuit diagrams (see Diagnostics Information System),
in a rational sequence with the prescribed tools (special tools) and taking into account the 
relevant health and safety regulations.

 

Installation information

 

The retrofit wiring harness is to be installed so that it cannot kink or chafe.
 If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must 
be used.
All work is shown on a LHD car. On RHD cars some work must be completed the opposite way 
round.
All tightening torque values are to be taken from the current repair manuals and must be 
observed.

 

Safety instructions

 

The current accident prevention regulations must be followed.

Содержание 66 20 0 007 031
















Отзывы: