BLUM AVENTOS HF Скачать руководство пользователя | Manualshive

Страница: 19 / 24

background image

We recommend the following troubleshooting sequence.

Problem

Possible cause

Remedy

NOTICE

When using several SERVO-DRIVE switches in one cabinet, all

SERVO-DRIVE switches must be checked individually.

Troubleshooting

1

Front does not move
either by pressing on
the front or pressing the
SERVO-DRIVE switch

Front and/or SERVO-DRIVE switch
was not pressed long enough

Make a deliberate effort to press the
front and/or SERVO-DRIVE switch
(to the full extent of travel)

Front and/or SERVO-DRIVE switch
was pressed too long (leaning pro-
tection triggered)

Press the front and/or SERVO-
DRIVE switch for a briefer time

Blum transformer is not connected
to the power outlet

• Connect the flex to the Blum trans-

former and to the power outlet

• Turn on the switched outlet

Battery was inserted incorrectly into
the SERVO-DRIVE switch
╵→ Battery display on the SERVO-

DRIVE switch lights red

Insert battery correctly

Drive unit is not attached properly to
the lift mechanism

Correctly install drive unit

The SERVO-DRIVE switch is not
activated

Activate the SERVO-DRIVE switch

Collision avoidance was activated
in error
╵→ A second front would be open if

this scenario is correct

Deactivate collision avoidance

Battery is dead

Replace battery

SERVO-DRIVE switch is defective

Replace SERVO-DRIVE switch

Drive unit is defective

Replace drive unit

Cabling or Blum transformer is
defective

Replace cabling and/or Blum
transformer

19

«
...
17
18
19
20
21
...
»

Содержание AVENTOS HF

























Отзывы:

Нет отзывов

Похожие инструкции для AVENTOS HF

Бренд: Olimpia splendid Страницы: 40

POWER TIG 210EXT

Бренд: R-Tech Страницы: 27

Бренд: Autowel Страницы: 11

Бренд: GYS Страницы: 24

BOC Smootharc TIG 200 ACDC

Бренд: Linde Страницы: 48

BI-WELDER TIG 2040 DC-HF

Бренд: Cebora Страницы: 11

315P AC/DC Digital

Бренд: Jasic Страницы: 37

Aristo Mig 3001i

Бренд: ESAB Страницы: 76

Бренд: Parweld Страницы: 17

Бренд: Westweld Страницы: 18

Бренд: PDQ Страницы: 2

Бренд: Parkside Страницы: 37

Бренд: Jasic Страницы: 19

KUMJRRW200AC/DC

Бренд: Unimig Страницы: 48

Бренд: Buffalo Tools Страницы: 17

Бренд: Buffalo Tools Страницы: 28

Бренд: GEZE Страницы: 64

Бренд: LORCH Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды