manualshive.com logo in svg

Blueworks BLH Series, Инструкция по технике безопасности

Поделиться
Скачать
Blueworks BLH Series Скачать руководство пользователя страница 26

26 |

P a g e

rights, which vary from state to state. This warranty supersedes all
previous publications. Any dispute between the original purchaser and
Products will be settled by binding arbitration, conducted in
Mecklenburg County, NC, under the rules of the American Arbitration
Association.

Disclaimer:

This limited warranty is the entire warranty. No other

warranties apply, expressed or implied. This limited warranty gives you
specific legal rights, which varies accordingly from state to state. Under
no circumstances shall the manufacturer or authorized agents/installers
be responsible for consequential, special, or incidental damage(s) of
any kind, including but not limited to personal injury. Property damage
or damage to or loss of equipment.
The manufacturer or agents/installers are not liable for any other
expenses that may be encountered during installation or servicing.
Authorized agents/installers may charge a trip fee for warrant-able
service work.
Some states do not allow the exclusion of limitations of incidental or
consequential damages.
Listed exclusions and limitations may not apply to you.
During the full coverage warranty process, we cover all replacements,
repairs and labor cost. The customer is responsible for shipping to and
from our warranty center.

Содержание BLH Series
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды