Blue-White CHEM-FEED MD3 Series, Руководство по эксплуатации

Страница: 24 / 40

4.3.9 Proportional Dosing
Used to configure proportional Parts Per Million dosing to a system. This method
of proportional dosing is based off an input signal the pump is receiving from an
external flow meter. The flow meter must have a high speed pulse output >10Hz.
You will need to refer to flow meter instruction manual to obtain the K-factor for
the flow meter.
Default settings: 12.5% dose solution concentration
1.25 dose solution Specific Gravity
5.0 K-factor (Pulses Per Liter),
see flow meter instruction manual
1.0 Parts Per Million to dose
Press MODE button until Proportional Dosing is displayed in the top line of the
display.
To configure the pump, navigate to Proportional Dosing menu by using the
short-cut method described at the beginning of the section, or by pressing
MENU button, then selecting Input Setup, Input Modes, and then
Proportional .
Press UP or DOWN arrow to scroll through 0 - 9 on selected digit.
Press RIGHT arrow to scroll over to next digit to the right. If you pass your
desired digit, you can easily scroll back by continuously pressing RIGHT button.
Press ENTER to save the changes.
Continue this process until all four screens have been configured.
If you used the short-cut to enter Proportional Dosing setup, press and hold
Mode button until Run Mode screen is displayed.
If you used the Menu button to navigate to Proportional Dosing setup, you must
navigate back out of menu structure. To do this you must select <-Esc at bottom
of every screen menu until you see Run Mode screen displayed.
- Proportional Dosing
Input K-Factor (pulses):
Pulses Per Liter.
0.0001 - 9999.9999
- Proportional Dosing
Dose Specific Gravity:
Specific Gravity of solution.
Press ENTER to set.
.25 1
- Proportional Dosing
Dose Concentration:
Percentage of concentration.
Press ENTER to set.
- Proportional Dosing
PPM to dose:
Parts Per Million to dose.
000.0 - 100.0 PPM
0 12.5%
0 005.0000
0 01.0
Injection
Point
S3 Series | Hybrid Ultrasonic Flowmeter
NEMA 4X
IP 66
Industries, Ltd.
ProSeries
by Blue-White Ind.
TM Doppler /
Transit Time
Discharge
Line
Paddlewheel
Flow Sensor / Meter
Ultrasonic
Flow Meter
Injection
Point
Example #1, Ultrasonic flow meter Example #2, Paddlewheel flow meter
Discharge
Line
or
- Menu
+ Configuration
+ Input Setup
+ Pump Output
<- Esc
- Input Setup
+ Contact Closure Input
- Contact Closure Input
Close: Stop Pump
Open: Stop Pump
<- Esc
Hidden
+ Motor - Select RPM
+ Tubing - Max Flowrate
+ Set FVS
+ Operating Input Modes
Disable
Done
4.4 Contact Closure Input (Remote Start/Stop)
Used to remotely start and stop the pump using a close=stop or open=stop
signal. If the pump must start when the loop is open, then select “Close: Stop
Pump” option. Can be used with an external foot pedal, a PLC, contact closure,
or other similar external devices.
Default settings: Disable
CC Input Range: 6 - 30 VDC
or
Dry Contact Closure (no voltage required)
[See section 5.1 for wire connections]
Navigate to Contact Input menu by MENU button, then selecting Input Setup,
and then Contact Input .
Press UP or DOWN arrow to scroll through your options.
Press ENTER to make a selection. You should then notice the radio button
(square box) is now filled in next to your selection.
Press DOWN arrow to scroll down to Done selection. Then press ENTER.
To prevent false triggering due to flickering (high speed) electrical switches, a
trigger delay time can be configured to delay the pump command. The delay
time unit of measure is seconds. A two second delay time is recommended.
To navigate back out of menus, select <-Esc and press the ENTER button at the
bottom of every screen menu until you see the Run Mode screen displayed.
IMPORTANT: To begin operation, press the START button to place pump in
STANDBY. The display background will turn blue indicating the pump has been
stopped remotely. When the pump is started by the remote contact, the display
background will turn green.
IMPORTANT: If the Contact Closure Input is enabled, the pump will display
STANDBY if the pump has been stopped by the Remote Contact Closure.
Please use caution in this mode as the pump may Start at anytime. If you
must perform maintenance to the pump, Press STOP button.
When Contact Closure Input is enabled, the word Remote will always be
displayed on the lower left side of the display screen.
Manual Speed Adjust
Waiting for SIGNAL...
STANDBY
REMOTE
Manual Speed Adjust
GAL/DAY
228
Å
É
ÄÈ
REMOTE
Signal stopped pump
Signal started pump
Remote Delay
Input Remote Delay
Max Delay = 999.9 (s)
Press ENTER to set
0 00.0
Page 24 Page 25
®
CHEM-FEED MD3
®
CHEM-FEED MD3