background image

9 VDC 1A power 

supply (regulated) 

with a 5.5 x 2.1 x 9.5 

center positive 

connector 

Back Side View

Front Side View

Side View

Mount XLR connector as desired.

Recommended wire: 24 AWG 

stranded & twisted together.

Analyzer Board

DMX 

Wire

Analyzer Board

FRONT

BACK

Set the Voltage Regulator Jumpers according to the voltage input 
that will be used. If +5VDC is to be connected set the jumpers to 
the OFF position. This will disable the regulator and the connected 
power source will power the PCB directly. If a power source is 
connected that is in the range of +7VDC ~ +15VDC then set the 
jumpers to the ON position.  For example, use this setting for a 6 
cell battery pack with 1.5V batteries totaling 9V. 

REGULATOR

POWER

Custom Equipment, Unique Electronic Products

Phone (303) 651-3794

Blue Point Engineering

www.BPEsolutions.com

Blue Point   

Engineering

Instruction

I

Pointing the Way to Solutions!

Jumper Setup 

Fuse

Power 
Connection

+

-

DMX  Data Analyzer Board  - Setup

POWER INPUT SETTINGS AND CONNECTIONS

Assemble the power setup harness or power connection cable 
and attach to PCB (Optional kit- not included) 

Suggested Battery Schematic

7V - 15VDC Power Harness

Switch

Power

Connection

Battery

Pack

+VDC to 

Circuit 

GND to 

Circuit

SC1047 1

3

2

1

3

2

1

3

2

SC1047

Bottom

View

Note: 
Ground is switched by inserting a connector

5-15 VDC POWER

HARNESS

REGULATOR

OFF

ON

5VDC

7V to 15V

Input

Input

NOTE - If a voltage source greater than 12VDC is used it is 
recommended to remove and mount the regulator to the 
metal chassis or a heat sink to dissipate excessive hea

t

.

N O T E :

DO NOT EXCEED THE VOLTAGE RANGE.
DO NOT SOURCE OTHER DEVICES FROM THIS  PC BOARD.
INSURE THAT THE VOLTAGE SOURCE IS A REGULATED DC VOLTAGE

Power Jack

GND

+

-

2.1 x 5 x 9 mm

Содержание DMX Analyzer













Отзывы: