Blue Diamond HD 2 Series Скачать руководство пользователя страница 12

Connecting Attachment To The Skid Steer

Cont’d

Enter  the  operator’s  position.  See  “Entering  The
Operator’s Position” on page 19.

Drive  the  machine  slowly  forward,  until  the  top
edge of the machine’s mounting plate is under the
top flange of the attachment mounting frame.

Slowly tilt the machine’s mounting plate back until
the attachment mounting frame fully contacts the
front of the machine’s mounting plate.

Leave  the  operator’s  position.  See  “Leaving  The
Operator’s Position” on page 19.

WARNING

AVOID SERIOUS INJURY OR DEATH

The  locking  pins  /  wedges  must  extend
through  the  holes  in  the  attachment
mounting  frame.  Failure  to  secure  locking
pins / wedges can allow attachment to come
off.
SEE  MACHINE’S  OPERATOR’S  MANUAL
FOR ADDITIONAL INFORMATION.

Engage attachment locking levers / wedges (See
the  machine's  Operator’s  Manual  for  detailed
information).

Connecting Hydraulic Hoses

IMPORTANT

Thoroughly  clean  the  quick  couplers
before  making  connections.  Dirt  can
quickly damage the hydraulic system.

Remove  dirt  or  debris  from  the  male  and  female
couplers.  Visually  inspect  the  couplers  for
corroding,  cracking,  damage,  or  excessive  wear.
Replace as needed.

Connect  the  attachment  hydraulic  hoses  to  the
machine.  Pull  on  each  hose  to  verify  full
connection is made.

Disconnecting Hydraulic Hoses

WARNING

AVOID BURNS

Hydraulic  fluid,  tubes,  fittings  and  quick
couplers  can  get  hot  during  operation.  Be
careful when connecting and disconnecting
hydraulic hoses.

Relieve  auxiliary  hydraulic  pressure.  (See  the
machine’s  Operator’s  Manual  for  correct
procedure.)

Disconnect  attachment  hydraulic  hoses  from  the
machine.

Blue Diamond® Attachments

12

Содержание HD 2 Series





















































Отзывы: