Blue Box KAPPA V 2001, Руководство по эксплуатации, установке и техническому обслуживанию

Страница: 38 / 70

31
If the unit fails to start: If the unit fails to start:
If the unit fails to start: If the unit fails to start:
If the unit fails to start:
DO NOT tamper with the internal electrical connections; this invalidates the warranty.
DO NOT tamper with the internal electrical connections; this invalidates the warranty.
DO NOT tamper with the internal electrical connections; this invalidates the warranty. DO NOT tamper with the internal electrical connections; this invalidates the warranty.
DO NOT tamper with the internal electrical connections; this invalidates the warranty.
5.3 5.3
5.3 5.3 5.3 COMMISSIONING
COMMISSIONING
COMMISSIONING COMMISSIONING COMMISSIONING
Close the main power switch before commissioning the unit.
Refer to the controller instruction manual for the commissioning procedure.
- Close the external interlock
- Push the key “ON” of microprocessor control
- If all the permissive are available, the display will show “UNIT ON”
After the procedure has been completed, the unit will automatically start with a delay of about 5 minutes when
the microprocessor control, flow switch and circulator pump permissives are available.
5.2.19 Operation with outlet water temperature (option) 5.2.19 Operation with outlet water temperature (option) 5.2.19 Operation with outlet water temperature (option) 5.2.19 Operation with outlet water temperature (option) 5.2.19 Operation with outlet water temperature (option)
For control of outlet water temperature, the reference probe must be installed at the exchanger outlet, or in the
case of several exchangers, in the common water outlet after the manifold.
The activation of unit power steps depends on activation and deactivation delays in relation to a dead band.
When the reference water temperature exceeds the set point without leaving the dead band, no outlets are
enabled or disabled to lower the water temperature; when the reference water temperature exceeds the sum of
the set point value and the dead band, a unit power step (e.g. start-up of a compressor or the transition to full
capacity operation of an active compressor) will be activated.
Caution: For heat pump installations, the mode of operation should be switched seasonally only. Caution: For heat pump installations, the mode of operation should be switched seasonally only. Caution: For heat pump installations, the mode of operation should be switched seasonally only. Caution: For heat pump installations, the mode of operation should be switched seasonally only. Caution: For heat pump installations, the mode of operation should be switched seasonally only.
Frequent switching between summer and winter operation can damage the compressor and
Frequent switching between summer and winter operation can damage the compressor and Frequent switching between summer and winter operation can damage the compressor and Frequent switching between summer and winter operation can damage the compressor and Frequent switching between summer and winter operation can damage the compressor and
result in failure.
result in failure. result in failure. result in failure. result in failure.
Disconnect the unit power supply only in case of prolonged disuse (e.g. Disconnect the unit power supply only in case of prolonged disuse (e.g. Disconnect the unit power supply only in case of prolonged disuse (e.g. Disconnect the unit power supply only in case of prolonged disuse (e.g. Disconnect the unit power supply only in case of prolonged disuse (e.g.
seasonal shutdown). Disconnecting the power supply to the unit also
seasonal shutdown). Disconnecting the power supply to the unit also seasonal shutdown). Disconnecting the power supply to the unit also seasonal shutdown). Disconnecting the power supply to the unit also seasonal shutdown). Disconnecting the power supply to the unit also
disconnects the casing heater, thus resulting in damage to the compressor
disconnects the casing heater, thus resulting in damage to the compressor disconnects the casing heater, thus resulting in damage to the compressor disconnects the casing heater, thus resulting in damage to the compressor disconnects the casing heater, thus resulting in damage to the compressor
when the unit is started up again. For temporary shutdowns, follow the
when the unit is started up again. For temporary shutdowns, follow the when the unit is started up again. For temporary shutdowns, follow the when the unit is started up again. For temporary shutdowns, follow the when the unit is started up again. For temporary shutdowns, follow the
instructions in paragraph 5.6.
instructions in paragraph 5.6. instructions in paragraph 5.6. instructions in paragraph 5.6. instructions in paragraph 5.6.