© 2009 Blue Angel™ Pumps
330804-002 12/09
Sewage Pump
CSE40M, CSE40T
CSE40T-2 and BCAPSE40
Operating Instructions and Parts Manual
Please read and save these instructions. Read carefully before
attempting to assemble, install, operate or maintain the product
described. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result in
personal injury and/or property damage! Retain instructions for
future reference.
Description
A sewage pump is intended for use in
domestic sewage lift stations. It is suitable
for pumping sewage, effluent, wastewater,
groundwater, and other nonexplosive,
noncorrosive liquids with up to 2 inch solids.
The pump is controlled by a switch with a
piggyback style plug which accepts the pump
plug and, in turn, plugs into a 120-volt outlet.
The float switch is a wide angle differential
switch that rises with the liquid level and turns
the pump on. As the liquid level decreases,
the float lowers and turns the pump off.
The BCAPSE40 is provided with a solid-
state electronic water level control. When
water is detected, the pump will start
automatically. This pump is intended for
use in domestic sewage lift stations.
Unpacking
Inspect this unit before it is used.
Occasionally, products are damaged
during shipment. If the pump or
components are damaged, return
the unit to the place of purchase for
replacement. Failure to do so could
result in serious injury or death.
The Professional’s Line
For parts, product & service information
visit
www.blueangelpumps.com
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
Performance
GAllONS PER MINUTE AT TOTAl
hEAD IN fEET
5
10
15
90
62
23
Safety Guidelines
This manual contains information
that is very important to know and
understand. This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help
recognize this information, observe the
following symbols.
Danger indicates
an imminently
hazardous situation which, if not avoided,
WILL result in death or serious injury.
Warning indicates
a potentially
hazardous situation which, if not avoided,
COULD result in death or serious injury.
Caution indicates
a potentially
hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
Notice indicates
important
information, that if not followed, may
cause damage to equipment.
General Safety
Information
CAlIfORNIA PROPOSITION 65
This product or its
power cord contains
chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
GENERAl SAfETy
1. Know the pump application,
limitations, and po ten tial hazards.
Do not
use to
pump flammable or
explosive fluids such as
gasoline, fuel oil, kerosene,
etc. Do not use in a
flammable and/or explosive atmosphere.
Use pump only with liquids compatible
with pump component materials. Failure
to follow this warning can result in
personal injury and/or property damage.
2. Make certain that the power source
(electric motor) conforms to the
requirements of the equipment.
Disconnect power before
servicing. If the power
dis con nect is out of sight,
lock in the open po si tion and tag it
to prevent unexpected application of
power. Failure to do so could result in
fatal electrical shock!
Specifications
BCSE50M & BCSE50T
BCAPSE50 &
BCAPSE50-2
Power supply requirements
120V, 60 hz
120V, 60hz
Circuit requirements
15 amps (min)
15 amps (min)
Motor duty
Intermittent
Intermittent
Motor
120V, 1 Phase
120V, 1 Phase
Horsepower
4/10
4/10
Motor full load
12.0 amps
8.7 amps
Liquid temperature range
40°F to 120°F
40°F to 120°F
Max. operating position
45o from vertical
45o from vertical
Dimensions
14 inch x 12 inch
14 inch x 12 inch
Intake
2 inch
2 inch
Discharge
2 inch NPT female
2 inch NPT female
Cut-in level (factory set)
19 inch
11 inch
Cut-out level (factory set)
9 inch
3 inch
Differential
10 inch
7 inch
Switch
90° wide angle
mechanical tether switch
Capacitive water sensor
Power cord
16 gauge 3 conductor
with plug
16 gauge 3 conductor
with plug
Construction
Motor
body material .......... Cold rolled steel
Motor housing ...................... Cast iron
Volute .................................... Cast iron
Impeller .............. Glass reinforced PBT
Seal plate .............................. Cast Iron
Shaft seal ........................... Mechanical
Содержание BCAPSE40
Страница 19: ...Notas 19 Sp CSE40M CSE40T CSE40T 2 y BCAPSE40 ...
