Blonder tongue HDE-8C-QAM w/Opt 2 Скачать руководство пользователя страница 8

Страница: 8 / 44

HDE-8C-QAM

Instruction Manual

Rear panel connectors are:

INPUTS #1 thru 8 + Spare:

RCA connectors for Video and Audio inputs marked as follows:

Y, Pb, Pr - Analog Component Video

Y – Composite Video

CC –

Analog NTSC Closed Captioning (EIA-608, also known as Line 21), which will then be digitized and

inserted in the MPEG-2 Transport Stream of the Component inputs.

L, R - Analog Left/Right Audio

QAM RF OUT:

“F” connector for up to four (4) QAM RF outputs.

EAS CONTROL:

Terminal strip to activate the EAS messaging feature in one of two the following ways:

a) 5-12 VDC between terminals 1 & 3 shown below

b) Dry Contact between terminals 2 & 3 shown below

NOTE:

This feature is intended to activate EAS and override all the input programs (whether Component or

Composite) with the EAS INPUT (see below for details). The QAM OUT (see above), and ASI OUT

(see ) will both contain the video and audio present at the corresponding RCA connectors

of the EAS INPUT.

EAS INPUTS:

RCA connectors for EAS Analog Audio (marked L & R) and Composite Video (marked Video) inputs.

INPUT POWER:

IEC 14 power inlet plug - rated 110/230 VAC; 1.2/0.6A; 60/50 Hz; equipped with Slo-Blo, 4.0 Amps, 250 V Fuse and

On/Off switch.

RECEIVERS CONTROL 10/100 :

RJ45 connector for 10/100Base-T Ethernet interface for controlling satellite receivers.

CONTROL 10/100:

RJ45 connector for 10/100Base-T Ethernet interface for monitoring and configuring the unit. Only static IP address

can be assigned to this interface. The factory default value is 172.16.70.1.

EAS feature is functional only when (i) EAS Control is triggered ON, and (ii) Video/audio is detected on

EAS INPUT connectors. The EAS feature will not be functional unless both these conditions are met.

1 2 3

Содержание HDE-8C-QAM w/Opt 2













































Результаты поиска

Содержание HDE-8C-QAM w/Opt 2

Отзывы:

Бренды по названию

Популярные бренды

Blonder tongue HDE-8C-QAM w/Opt 2, Руководство пользователя

Результаты поиска

Содержание HDE-8C-QAM w/Opt 2

Отзывы:

Бренды по названию

Популярные бренды