Blonder tongue HDE-8C-QAM w/Opt 2 Скачать руководство пользователя страница 6

Страница: 6 / 44

6 HDE-8C-QAM

Instruction Manual

Section 2 — Product Summary

2.1 Revision History & Reason

The second release of the manual added single part virtual channel numbering capability.

The third release updated the system connection diagram.

2.2 Product Application & Description

Application:

HDE-8C-QAM (MPEG-2 HD Encoder – 8xComponent/8xComposite – 4xQAM) accepts up to eight (8) analog programs from

any of the following inputs: 8xComponent and 8xComposite. The encoder is equipped with a spare input (9th input) to

replace any one (1) of the primary eight (8) inputs in the event of a failure.

The encoder digitizes, MPEG-2 encodes each input into a high-definition stream, multiplexes the resulting eight (8)

program streams, and then modulates them onto four (4) adjacent QAM channels in the 54-1002 MHz range (CATV 2-158).

Any one (1) of the four (4) QAM output streams is also available in ASI format.

The encoder supports Dolby® Digital audio encoding, and Closed Captioning (EIA-608). It is also equipped with an

Emergency Alert System (EAS) interface. A front-panel RF test point allows for monitoring/testing of the QAM output

without service interruption.

The encoder accepts eight (8) primary analog programs and one (1) spare from DIRECTV Network’s H25-100 satellite

receivers. Remote monitoring and control of the nine (9) satellite receivers is accomplished through UPnP protocol via

a rear-panel 10/100Base-T Ethernet connection using a standard Web browser. An Ethernet switch with a minimum of

5 ports and two (2) DirecTV DECA units are required for connecting the receivers to the encoder’s receiver control port.

Dolby is a registered trademark of Dolby Laboratories.

Features:

• Accepts up to 8 programs from any of the following inputs: 8xComponent and 8xComposite

• Supports additional 1 spare input to replace the failed input

• Digitizes, MPEG-2 encodes, and multiplexes up to 8 inputs into 4 QAM output channels (2 programs per QAM channel)

• Provides any 1 of the 4 QAM output streams in ASI format

• Compatible with ITU Annex A and B digital QAM formats

• Provides comprehensive GUI-based monitoring and control via standard Web browsers

• Provides a front-panel RF test point (at 20dB below primary QAM output)

• Equipped with EAS interface (Analog Video + L/R Audio)

• Supports Real-time Dolby® Digital audio encoding

• Supports Closed Captioning EIA-608

• Supports user-defined PSIP configuration

• Controls STB receivers through UPNP

RG-6

Refer to DirecTV

installation procedures

RX#1

A/V Cables

RX#8

Control & Monitoring

DT-16PT100M-RM

Receiver

Control

DT-05PT100M

PC w/web

browser

CAT 5

SWS-8WBMC

9501-M

DECA Power Supply

Power Supply Port

BBDECA

SPARE

Ethernet Port

Connect the equipment as follows:

Содержание HDE-8C-QAM w/Opt 2













































Результаты поиска

Содержание HDE-8C-QAM w/Opt 2

Отзывы:

Похожие инструкции для HDE-8C-QAM w/Opt 2

Бренды по названию

Популярные бренды

Blonder tongue HDE-8C-QAM w/Opt 2, Руководство пользователя

Результаты поиска

Содержание HDE-8C-QAM w/Opt 2

Отзывы:

Похожие инструкции для HDE-8C-QAM w/Opt 2

Бренды по названию

Популярные бренды