Blonder tongue 6522B-4-64 Скачать руководство пользователя страница 19

Страница: 19 / 48

EQAM-420B

User Manual

In the section entitled

“Status”

under the blue header, the following parameters about each source IP stream are

displayed:

Stream:

the user must update the source IP stream information in the following format:

xxx://yyy.yyy.yyy.yyy:zzzzz

where,

xxx = the protocol / encapsulation method of the source (IP) stream. The only acceptable protocols are

UDP or RTP.

yyy.yyy.yyy.yyy = IP address of the source stream.

zzzzz = port number of the source stream.

Example 1:

Assume that the source stream is (i) using UDP protocol, (ii) in Multicast format, (iii)

provided from IP address 225.16.70.20, and (iv) on port 50001. Then the address must be entered as:

UDP://225.16.70.20:50001.

Example 2:

Assume that the source stream is (i) is using RTP protocol, (ii) in Multicast format, (iii)

provided from IP address 239.16.180.67, and (iv) on port 50000. Then the address must be entered as:

RTP://239.16.180.67:50000.

Example 3: Assume that the source stream is (i) using UDP protocol, (ii) in Unicast format, (iii) provided

from IP address 172.160.80.70, and (iv) on port 50000. Then the address must be entered as: UDP://

172.160.80.70:50000.

Source IP:

IGMP Version 3 adds support for "source filtering", that is, the ability for a system to report interest in

receiving packets *only* from specific source addresses, as required to support Source-Specific Multicast [SSM].

Name:

once the Stream information in above is updated, the unit auto-detects the name of the source

stream if assigned by the source. The user, however, is allowed to edit/update the current stream name. Up to 10

alphanumeric characters are allowed.

The IP address range for a Multicast stream must be between 224.0.0.0 and 239.255.255.255.

The unit will consider any address outside of this range to be a Unicast address.

Remember to click on the SAVE button to apply the new values/configurations.

The address entered here MUST be identical to the address of the source stream, or else the unit

cannot recognize the source (IP) stream. No duplicate IP addresses are allowed. If duplicate IP addresses

are entered, then the duplicate IP addresses will be highlighted in yellow as shown in Figure 6.2.4

Содержание 6522B-4-64

















































Результаты поиска

Содержание 6522B-4-64

Отзывы:

Похожие инструкции для 6522B-4-64

Бренды по названию

Популярные бренды

Blonder tongue 6522B-4-64, Руководство пользователя

Результаты поиска

Содержание 6522B-4-64

Отзывы:

Похожие инструкции для 6522B-4-64

Бренды по названию

Популярные бренды