Blomberg 8978983800 Скачать руководство пользователя страница 34

Страница: 34 / 70

BWOS 30100 SERVICE MANUAL

F05

Over
temperature
detected while
cooking
(t>650°f)

Runaway
temperature
condition
during
cooking.

One or more
relays are
stuck, driving
heating
elements.

Check the
contact of
relay

Replace the
power board

7.17

F06

Lower

Oven

F07

Over
temperature
detected in
self-clean
(t>950°f)

Runaway
temperature
condition
during self-
clean.

One or more
relays are
stuck, driving
heating
elements.

Check the
contact of
relay

Replace the
power board

7.17

F08

Lower

Oven

F09

Possible short
circuit on
display board
micro pins

Hardware
failure.

Humidity may
have created
condensation
on the
circuits.

Remove power
and dry the
board.

Short circuit
on display
board.

Replace the
display board.

7.19

F10

Possible short
circuit on
display board
circuits

Hardware
failure.

Humidity may
have created
condensation
on the
circuits.

Remove power
and dry the
board.

Short circuit
on display
board
connectors.

Check
connectors and
eventually clean
or replace the
board to board
cables.

Short circuit
on display
board.

Replace the
display board.

7.19

F11

Display board
eeprom data

Memory empty First power up

or new board
installed.

Configure the
oven model.
(resistor
configu
manual test)

2.5
2.6

Memory
cannot be
accessed

Bad memory
or circuit on
board.

Replace power
board

7.17

Bad cable

Check and

Содержание 8978983800







































































Результаты поиска

Содержание 8978983800

Отзывы:

Похожие инструкции для 8978983800

Бренды по названию

Популярные бренды

Blomberg 8978983800, Руководство по обслуживанию

Результаты поиска

Содержание 8978983800

Отзывы:

Похожие инструкции для 8978983800

Бренды по названию

Популярные бренды