Blomberg 8978983800 Скачать руководство пользователя страница 33

Страница: 33 / 70

BWOS 30100 SERVICE MANUAL



Each oven is equipped with two halogen lights located in the back wall of the oven.



The lights are switched on when the door is opened or when the oven is in a

cooking cycle.



The oven lights are not illuminated during SELF- CLEAN.



Each light assembly consists of a removable lens, a light bulb as well as a light

socket housing that is fixed in place. See Figure.



Light bulb replacement is considered to be a routine maintenance item.

4. TROUBLE SHOOTING GUIDE

4.1 ERROR MESSAGE

TO Reset assembly FAILURES, REMOVE THE CAUSE AND SWITCH THE SELECTORS IN

“OFF” AND “Preset assembly” POSITIONS RESPECTIVELY.

Code Error

Description Possible Cause Corrective Action

section

F01

Temperature
sensor

The control
reads out of
range values.

Temperature
sensor
shorted or
broken.

Replace the
sensor

7.14

F02

Lower

oven

Bad
connections

Check the
connectors and
the harness

Bad power
board

Replace the
power board

7.17

F03

Latch
mechanism

The control
can’t perform
any locking or
unlocking
cycle within
the maximum
allowed time.

Latch
mechanism
problem.

Latch motor
problem

Replace the
motor

7.8

Defective
latch micro
switch

Replace the
micro switch

7.9

Door micro
switch breaks
during self-
clean when
the door is
locked

Replace the
door micro
switch

7.10

Bad
connections

Check the motor
connections and
the micro
switches
connections

F04

Lower

Oven

Defective
power board

Replace the
power board

7.17

Содержание 8978983800







































































Результаты поиска

Содержание 8978983800

Отзывы:

Похожие инструкции для 8978983800

Бренды по названию

Популярные бренды

Blomberg 8978983800, Руководство по обслуживанию

Результаты поиска

Содержание 8978983800

Отзывы:

Похожие инструкции для 8978983800

Бренды по названию

Популярные бренды