background image

BWOS 30100 SERVICE MANUAL 

31 

3.9.3  To Delay the Start of Clean: 

1.  Follow steps 1 through 7 above. 

2.  Touch STOP TIME key and the hour to stop 

will begin flashing. 

3.  Use INC or DEC buttons to change the stop 

hour. 

4.  To change minutes, touch STOP TIME key. 

5.  Minutes to stop clean will flash. 

6.  Use INC or DEC buttons to change the 

minutes. Hold the key to change by 10 
minutes. 

7.  Press STOP TIME or wait a few seconds to 

confirm the new value. 

8.  Oven door will lock and display shows 

DELAY.  

9.  When the delay time ends, clean start. 

10. At the end of the programmed cleaning 

time, the oven will automatically turn off. 

11. End will appear on the display, CLEAN & 

TIME will flash until any time key is touched 
or the knob is moved to OFF position. 

 

TO CHECK CLEAN TIME OR STOP TIME 

during 

a delayed clean, simply press COOK TIME or 
STOP TIME buttons. 

 

3.10 

OVEN DOOR REMOVAL 

3.10.1  To Remove Door  

 

1. 

Open the door completely. 

2. 

Lift up the hinge bracket (1) into the 
slot (2). 

3. 

Hold the door firmly on both sides 
using both hands and close the door. 

4. 

Hold firmly; the door is heavy. 

5. 

Place the door in a convenient 
location. 

3.10.2  To Replace Door 

 

1. 

Insert the upper arms (3) 
of both hinges into the 
upper slots (6) and the 
lower arms (4) into the 
lower slots (7). The 
recesses (5) must hook 
on the lips (8). 

2. 

Move the hinge brackets 
(1) back down into 
position. 

3. 

Close and open the door 
slowly to assure that it is 
correctly and securely in 

Содержание 8978983800







































































Отзывы: