background image

6

INSTALLATION

Installation Instructions

1.  Select a location to provide drainage directly below 

the tangent draw-off. Allow sufficient rear clearance 

from wall for kettle cover to lift upright freely and com-

pletely without obstructions. 

2. 

Mark hole locations through flanged adjustable feet 

on KLT-__E models. Remove kettle. 

3.  Drill holes on marked hole locations, and insert ex-

pansion shields to accommodate 5/16” size lag bolts. 

4.  Reposition kettle. On KLS-__E models level by mak-

ing necessary adjustments on flanged feet. 

5. 

Bolt down kettle and seal with Silastic or other equiv

-

alent sealing compound. Sealant must be applied not 

only to bolt heads but also around flanges or pedestal 

base making contact with floor surface to fulfill NSF 

requirements. Wipe off excess sealant immediately. 

6. 

A control box with power supply equivalent to electri

-

cal 

7.  Rating of kettle should be located conveniently near-

by. 

8.  A waterproof electrical connection for power supply to 

rear of control housing must be provided. 

9.  Ground kettle to terminal provided inside control 

housing. 

10. Turn power ON and check for proper operation.

Содержание KLS-100E










Отзывы: