Blink Marine PKP-2400-LI Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 16

Blink Marine PKP-2400-LI Скачать руководство пользователя страница 12

Via Montefeltro, 6 – 20156 Milano (MI) – Italy

- 12 -

Tel. +39 (02) 3088583 – Fax +39 (02) 33406697

www.blinkmarine.com

–

[email protected]

PKP-2400-LI_J1939_UM_REV1.0

Address claiming procedure:

Under normal operation, the keypad application sends an Address Claim parameter group at
start up and waits up to 250ms for the other devices connected to the same network to send
a message containing the device’s address and name. The keypad checks every response and
compares the names to see who has the highest priority. If a device is already using the address
and has a higher priority, then a new address is selected and the process starts over. If the
keypad has a higher priority than the device in use then it waits for other systems to reply, while
the responding device will have to change its address and send an address claim itself. If no
message is received after the time (250ms) is up, then the device has claimed the address.

Address claim parameter group:

Priority = 6.
Destination Address should always be the Global Address FFh
Parameter Group Number (PGN) = 60928(EE00h).
Data Length = 8
Data = NAME field

Example:

Direction

Identifier

Format

Message

Data

From Keypad

18EEFF21h

Ext

3F 42 6F 1A 00 82 3C C0

«
...
10
11
12
13
14
...
»

Содержание PKP-2400-LI

















Отзывы:

Нет отзывов