background image

180-CL2714.SP v1.00

July 30, 2020

Page 41

Clarity CL2714 SP

Blaze King Gas Limited 10 Year Warranty

 

Blaze King is the manufacturer of the Blaze King line of heating products. At Blaze King, our commitment to the highest 

level of quality and customer service is the most important thing we do. Each Blaze King stove is built on a tradition of 

using only the finest materials and is backed by our limited lifetime warranty to the original purchaser. With Blaze King, 

you’re not just buying a fireplace or stove, you’re buying a company with years of unequalled performance and quality.

 

Limited 10 Year Warranty:

Under this warranty, Blaze King covers the fireplace or stove, exterior body, pedestals, legs and glass (thermal breakage 

only) against defects in materials and workmanship, for part repair or replacement for (10) years from original purchase 

date and limited labor for the first two (2) years to the original purchaser. This warranty does not cover exterior finishes. 

Please see the exclusions and limitation section below as certain restrictions and exclusions apply to this warranty.

Limited 5 Year Warranty:

Under this warranty, Blaze King covers the fireplace or stove firebox and heat exchanger against defects in materials and 

workmanship, for part repair or replacement for the first five (5) years and limited labor for the first two (2) years to the 

original purchaser. This Warranty covers: Heat Exchanger, Steel Firebox Panels and any steel components not covered 

under the ten (10) year Warranty excluding burner components and gas components. Please see the exclusions and 

limitation section below as certain restrictions and exclusions apply to this warranty.

Limited Two (2) Year Warranty:

Under this warranty, Blaze King covers: Gas Assembly, Burner components (ceramic and steel), Log sets, Blower and 

control, Temperature Sensors, thermocouple, thermopile, electronic ignition components and wire harness against 

defects in materials and workmanship, for part repair or replacement for the first two (2) years and limited labor for the 

first (1) year to the original purchaser. Please see the exclusions and limitation section below as certain restrictions and 

exclusions apply to this warranty.

 Limited One (1) Year Warranty:

Under this warranty, Blaze King covers all exterior surface finishes against defects in materials and workmanship, for 

part repair or replacement and limited labor for the first (1) year to the original purchaser. Please see the exclusions and 

limitations section below as certain restrictions and exclusions apply to this warranty.

How the Warranty Works (Includes Conditions, Exclusions and Limitations)

1. All warranties by the manufacturer are set herein and no claim shall be made against the manufacturer on any oral 

warranty or representation. All claims under this Limited Warranty must be made in writing by your dealer.

2. Any stove or part thereof that is repaired or replaced during the Limited Warranty period will be warranted under the 

terms of the Limited Warranty for a period not exceeding the remaining term of the original Limited Warranty or six (6) 

months, whichever is longer.

3. For any part or parts of this stove, which in our judgment show evidence of defects, Blaze King reserves the option to 

repair or to replace the defective product through an accredited distributor or agent, provided the defective part is returned 

to the distributor or agent, transportation prepaid, if requested.

4. If you discover a problem that you think may be covered by the Limited Warranty, you MUST REPORT it to your Blaze 

King dealer WITHIN 30 DAYS from the date the problem was first detected, giving them proof of purchase and the date of 

purchase.  The dealer will investigate the problem and work with Blaze King to determine whether the problem:

a) Is covered by the Limited Warranty or

b) Can be fixed in your home or does the product need to be returned to Blaze King for repair.

5. If Blaze King determines that the stove needs to be returned to Blaze King for repair, the customer has the 

responsibility and the expense of removing it from their home and shipping it to Blaze King. If the problem is covered by 

the Warranty, Blaze King will repair or replace the item at their discretion and the customer will be responsible for return 

shipping and re-installation in their home.

6. If the problem is not covered by the Limited Warranty, the customer will be responsible for all repair costs, as well as all 

storage, shipping and the cost of removing and re-installing the stove.

If you are not satisfied with the service provided by the Blaze King dealer, write to Blaze King at the address listed on the 

last page of the Owner’s Manual. Include a copy of the original purchase invoice and a description of the problem.

WARRANTY

Содержание CLARITY CL2714.SP













































Отзывы: