Blaze King CLARITY CL2714.SP Скачать руководство пользователя

Страница: 29 / 44

180-CL2714.SP v1.00

July 30, 2020

Page 29

Clarity CL2714 SP

INSTALLATION

VENT TERMINATION LOCATION

• In heavy snowfall areas make sure vent termination is located where it will not be blocked by snowfall or

snow from snow removal equipment.

•

Locate vent termination away from plants, bushes, or any other object on or near the vent termination that

will interfere or obstruct the air flow around it.

VENTING

This appliance will not function without being connected to a proper venting system. This unit is certified for

use with M&G Duravent, BDM, American Metal, Selkirk (Direct-Temp), Olympia, and ICC venting. Follow the

manufacturer’s installation instructions when installing the venting system, see venting instructions.

NOTE: Always check your local codes before installing venting. Necessary clearances and requirements may

vary from state to state (province to province). Do not pack air spaces with insulation.

Typical Installation

•

8’ (2.44 m) minimum vertical vent pipe on top of the appliance.

Horizontal Termination

•

One 90° bend, and up to 2’ (610 mm) maximum horizontal run to the outside horizontal cap with a minimum

8’ vertical pipe.

•

Clearances are in accordance with local installation codes and the requirements of the gas supplier.

Other installations

•

The total vertical height up to 36’ (10.97 m) maximum.

•

Use vent restrictor on vents from 20’ (6.09 m ) to 36’ (10.97 m) to obtain optimal flame appearance, see

“VENT RESTRICTOR” and “BURNER FLAME APPEARANCE”

NOTE: Maximum vent lengths may be subject to local codes.

For best venting performance, here are some general venting rules:

Use only vent systems and components certified for use with this appliance.

Observe all local code restrictions, if any, regarding the installation of this type of gas appliance.

3. Observe the vent height restrictions given in this manual.
4.

Terminate the vent with a termination certified for use with this appliance, see component list.

5. Ensure proper reassembly and resealing of the vent-air intake system when venting is installed,

inspected, or replaced.

Termination Above Roof

Consult local codes for minimum vent cap height

above the roof, vent must be a minimum 2’ from any

wall.

Install the flashing with upper portion slid under the

roofing material and the lower portion over the roofing

material.

NOTE: DO NOT FASTEN DOWN UNTIL THE FINAL

ADJUSTMENTS TO THE VENT HAVE BEEN MADE.

2ft (0.6m)

Minimum

3ft (0.9m)

Minimum

Within

10ft (3m)

Roof ridge or

any other portion

of a building

Содержание CLARITY CL2714.SP













































Результаты поиска

Содержание CLARITY CL2714.SP

Отзывы:

Похожие инструкции для CLARITY CL2714.SP

Бренды по названию

Популярные бренды

Blaze King CLARITY CL2714.SP, Руководство по эксплуатации и установке

Результаты поиска

Содержание CLARITY CL2714.SP

Отзывы:

Похожие инструкции для CLARITY CL2714.SP

Бренды по названию

Популярные бренды