Blaze King CLARITY CL2714.SP Скачать руководство пользователя

Страница: 1 / 44

180-CL2714.SP v1.00

July 30, 2020

CLARITY CL2714.SP

DIRECT VENT GAS FIREPLACE INSERT

with 7 Day Shutoff Standing Pilot (SP)

For use with natural gas (NG) or propane (LPG)

OPERATION & INSTALLATION MANUAL

Installer: Please complete the details on the back cover and leave this manual with the

homeowner.

Homeowner: Please keep these instructions for future reference.

Pour la version française de nos manuels S.V.P. vous référez à notre site web: www.blazeking.com

Date Installed:

Serial No.:

WARNING: If the information in these instructions are not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of life.

PFS report#:F18-431

A safety screen designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at-risk individuals. If the safety screen becomes damaged,

the safety screen shall be replaced with the manufacturer’s

safety screen for this appliance.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings

exactly could result in serious injury,

death, or property damage.

—

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

—

WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not

use any phone in your building.

•

Leave the premises.

•

Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call

the fire department.

—

Installation and service must be

performed by a qualified installer, service agency

or the gas supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA only) or

mobile home, where not prohibited by local codes.

This appliance may be installed in an OEM Installation in a

manufactured home (USA only) or mobile home and must be

installed in accordance with the manufacturer’s instructions

and the Manufactured Home Construction and Safety

Standard, Tittle 24 CRF, Part 3280, in the United States, or the

Standard for Installation in Mobile Homes, CAN/CSA Z240 MH

Series, in Canada.

This appliance is only for use with the type of gas indicated

on the rating plate. This appliance is not convertible for use

with other gases, unless a certified kit is used.

Содержание CLARITY CL2714.SP













































Результаты поиска

Содержание CLARITY CL2714.SP

Отзывы:

Похожие инструкции для CLARITY CL2714.SP

Бренды по названию

Популярные бренды

Blaze King CLARITY CL2714.SP, Руководство по эксплуатации и установке

Результаты поиска

Содержание CLARITY CL2714.SP

Отзывы:

Похожие инструкции для CLARITY CL2714.SP

Бренды по названию

Популярные бренды